Tech/maintenance 1946 The Martin Tenor - an overhaul thread

This was bottle of BKF paste, applied to a cotton terry cloth, then either gentle or medium scrubbing. No brush. Then a simple wipe down with a clean part of the towel.

I'm very pleased with the results! I figured I couldn't make it any worse, so did a small spot, and it came up with minimal effort. Some dark spots took more effort, but still I'd consider minimal. Not perfect, but it's 80 years old!
Great results ! Non abrasive too. I don’t care for Brasso.
Finally a good use for rhubarb 🤣
I assume you either made a paste from powder or used the soft cleanser ?
Either the company recommends a water rinse afterwards. Removes residual oxalic acid.
1787103154738.webp
 
Great results ! Non abrasive too. I don’t care for Brasso.
Finally a good use for rhubarb 🤣
I assume you either made a paste from powder or used the soft cleanser ?
Either the company recommends a water rinse afterwards. Removes residual oxalic acid.
View attachment 36615
I used the Soft Cleanser. Worked great as seen in results above. I may wet a rag and wipe it down then dry with another rag. Then coat areas with lemon Pledge once done.
 
I have been very busy lately and havent worked on the Committee much.

Last week I went over the body with BKF and give it a good once over. Its already starting to re-tarnish and has a dark gold hue.
11798.webp



Today I did the keys with BKF to clean them up. They turned out pretty nice! Some still have patches of lacquer. Low B and Bb lacquer is pretty much fully intact.
11797.webp
 
Looks like we'll be moving back to CO for my work. Not heartbroken as I don't care for FL anyway.

My ability to work on the sax will be delayed. In case we moved faster, I put it back together as is (no pads or corks) to make transport safer (and to not lose anything).
11812.webp

11813.webp
 
Nice old original rollers. Pick all the crud out of the slots. Tighten-loosen-tighten-loosen-tighten-loosen-…wiggle, repeat. Go gently and be thrilled if the come out easily and actually separate/ freely as two bits. Sometimes the pin will turn and the roll is stuck on rust. Music Medic sells Alum to dissolve the steel for this issue. New pin is necessary. Personally I’ve never had any luck with this technique.
I've yet to try it, but if I were I'd get the Alum on amazon for about half the price.
 
Well, we made our move back to CO. Just in time to have a nice fall!

All saxes survived well and I am eager to find a place to play now that we are in a condo rather than a single family home.

I am also eager to get work moving again on this tenor. I need to order pads, corking/felts, remove a few dents, get a new spring for the neck octave mechanism, and fix the side F# tone hole leak.
 
Florida to Colorado is a big move. I'm guessing it's work related. I can't imagine moving again, we've accumulated so much crap over the years. Although it would be a good cleansing. I wish you all the best.
 
Florida to Colorado is a big move. I'm guessing it's work related. I can't imagine moving again, we've accumulated so much crap over the years. Although it would be a good cleansing. I wish you all the best.
It's not bad. We didn't have a lot anyway to begin with. Still ended up selling quite a bit.

Work related yes and also it's much nicer out here so I can't complain about that!

Only tricky bit is that we are in a condo now so playing has become harder. I can play at work after hours and also spoke to the manager at the local music & arts store and he is fine with me playing there for free. Very nice guy. I'll be buying them lunch and will get my reeds from them I think.
 
Whew! It's been a long month of moving in and getting settled. But I've been itching to work on the Tenor again.

I finay ordered pads, corks, felts, shellac, and more from MusicMedic today.

Went with SoftFeel with flat resonators. Sent them my measured cups and pad sizes to get the best possible fit.


I also ordered a Meyer 5m Alto clone(3dsaxpro) on ebay last week, that came in on Mon and I tried it out. I like it! Though I plan to try a brand new reed on it as it was not fantastic feeling or sounding. I love the Bari Hybrid, but it's a 7(.82) and I wanted something a little bit smaller too. If I end up liking the 5m that much, I'll look at buying a real 5m. The Bari can really scream and go softly, but I think it takes too much air than I can give at this point, so figured I could build up to it over time, now that I'm at elevation too. Which also will help me build up my embouchure better too. I feel it get tired after ~45 minutes on the Bari.
 
No update from MM yet on all the stuff ordered. Maybe they are slammed? I'd like to be able to work on it some in the next few weeks.

While at the local music store tonight, I brought my tenor and have been looking to get a new case. The one the Handcraft came with is very old and falling apart. They had a Wolfpak case on clearance and it actually fit the Martin! I was shocked. We'll I got that and when I got it home, it fit the Committee III too! It fit both of the necks, though I will need to massage the foam a little to better fit the CommIII neck (it's longer slightly, plus the screw).

Now it is by no means perfect or as nice as many other cases. But for $50, it couldn't be beat. Its a lot easier to carry and more secure than the 2 clasp old case the HC came with. I am always gentle and careful with things, so I am not concerned. I could see a kid beating up a case of this quality and it not lasting. Since I am not a gigging musician or pro, I think this will suit just fine for the time being.

Just thought I'd mention this to anyone looking for a halfway decent case for either a HC or CommIII tenor that doesn't cost $200+.
 
No update from MM yet on all the stuff ordered. Maybe they are slammed?
You’re not the only one 🤨
While at the local music store tonight, I brought my tenor and have been looking to get a new case. The one the Handcraft came with is very old and falling apart. They had a Wolfpak case on clearance and it actually fit the Martin! I was shocked. We'll I got that and when I got it home, it fit the Committee III too! It fit both of the necks, though I will need to massage the foam a little to better fit the CommIII neck (it's longer slightly, plus the screw).

Now it is by no means perfect or as nice as many other cases. But for $50, it couldn't be beat. Its a lot easier to carry and more secure than the 2 clasp old case the HC came with. I am always gentle and careful with things, so I am not concerned. I could see a kid beating up a case of this quality and it not lasting. Since I am not a gigging musician or pro, I think this will suit just fine for the time being.

Just thought I'd mention this to anyone looking for a halfway decent case for either a HC or CommIII tenor that doesn't cost $200+.
That’s a smoking deal ! I just looked up the product. Thick layer of cloth covered foam. And a hard shell ? Covered with Cordura cloth.
Is the outer shell hard ?
 
At least I'm not in any huge rush. But I would like to work on it at least some during the Thanksgiving holiday.

I'm not entirely sure if it is hard shell. I can check it out more. Seems pretty sturdy. Like I said, not the greatest, but very workable if taken care of. The foam is decently hard and the covering is soft. Definitely more protection than the hardcase the tenor came in that is ~100 years old. The bow guard on the HC keeps it tight in there, the CommIII lacks that big bow guard, so a small piece of foam against the bell would wedge it in perfectly. Even then it doesn't move much. The pinky table of the CommIII fits well too, rested nicely against the formed section.

It was a pleasant surprise. Even with the tenor and everything in the new case, the old case weighs significantly more.
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,060
Messages
578,347
Members
8,128
Latest member
Roger Atlas
Back
Top Bottom