John Laughter
Member
- Messages
- 634
- Location
- Macon,GA
Disagree. Lubrication permits the screw to properly engage the threads without binding, extending the life of the threads.Lubrication enables more torque to be applied and will stress the screw, promoting premature failure. Brass isn't steel.
Not a bad idea. I could get some 1/8th inch square K&S brass stock, bend me a holder with small aircraft, race car, etc. to mount, my virtual Klangbogen.I noticed recently little figurines, angels etc for sale, that fit into your empty lyre socket. Purely decorative, useless and fun.

Mr PigSquealer will now have a flying pig no doubt..I noticed recently little figurines, angels etc for sale, that fit into your empty lyre socket. Purely decorative, useless and fun. I think we get too focused on functionality and forget whimsy and silliness. Who wouldn't want some little effigy of a mythical being or hero stuffed into their lyre socket for no apparent reason. π€
You got a point. I've replaced overtightened self-tapping screws in various plastic cased appliances around the house and musical instrument electronics to include radios, amps, speakers, even plastic car panels, where previous owner thought he was doing good. Over time, a universal ATX computer case needs an oversized, because the only thing holding the scrrew in place is the sheet metal behind without a spot welded nut. Sometimes it is not another's fault, just a poor design. (And a few times younger I played the guerilla.) π³Don't Blame Me.
![]()
Looking into this new technology as we speak. Prototype without wings and dry fit shows potential. Will attempt a test with a high pressure waterproof anti crossive grease. Chops Lube for screwy needs appears to be marketable.Mr PigSquealer will now have a flying pig no doubt..
Needs to have a catchy title. Klangensnout Lube? For that discerning Razorback. πChops Lube for screwy needs appears to be marketable.
A bit of an undignified position for the poor old piggy there, I was thinking something a bit more 'heroic' tbh πLooking into this new technology as we speak. Prototype without wings and dry fit shows potential. Will attempt a test with a high pressure waterproof anti crossive grease. Chops Lube for screwy needs appears to be marketable.
View attachment 30123
I'll take one even though my main horn doesn't have a lyre slot.Looking into this new technology as we speak. Prototype without wings and dry fit shows potential. Will attempt a test with a high pressure waterproof anti crossive grease. Chops Lube for screwy needs appears to be marketable.
View attachment 30123
I've made a bunch of them myself and tried them all, including a spectrum analyzer. The ligature worked better but I didn't like the look too much.
That was exactly my point in one of the other threads - somewhere here on the cafe - where the effect of ligatures was discussed. Even the slightest change in embouchure, reed alignment etc. has a much greater impact on tone than any of the "boosters - bΓΆgen - screws"@LostCircuits Have you played with the spectrum analyzer to learn how much you can vary the spectra using only physical inputs (oral cavity, embouchure, etc.) while keeping setup constant? I can hear a substantial variation in my tone while manipulating my inputs. I wonder how those scale compared to the effect of a ligature or K-bogen. The next order of interest would be mapping the spectra of various reeds (ex. changing reed stiffness, changing reed cut).
Why does it make perfect sense? When it doesn't make any sense at all? The material of a reed matters, I give you that.Iβm no scientist. More like a junkyard tech, but it makes perfect sense that the material of a lig matters. Say a Rovner compared to Francois Louis lig. Rubber Vs metal.
Perhaps your tech during COA lubricated it for you, so you did not have to do it? I go for long periods without lubbing it. But if I notice it acts like it needs it, then I do it; same with keys. But then my saxes were not maintained by a tech until recently. I was doing my own teching, which may explain oddities. And because I speak from memory, since I don't keep records, even that sometimes is more by premonition (if you know what I mean).I guess lubricating the neck tenon screw would do no harm, but I've been using my Mark VI tenor for 45 years on a very regular basis, and I've never lubricated that screw. It has always worked smoothly and still does to this day.
Good point. And yeah, I thought of that. You could well be correct. I have an excellent tech.Perhaps your tech during COA lubricated it for you, so you did not have to do it?
+1. I learned my lesson on this many years ago when my Mark VI tenor became nearly unplayable. At the time, I didn't realize it needed to be checked out once in a while (at least every couple of years, or more often depending on how much you play). The horn was full of leaks and needed a complete overhaul. Once that was done, it was like a brand-new horn, maybe better. Since then, I've kept it pretty well-maintained. Usually, it will need a couple of pads replaced, depending on how long I let it go. I did recently get a re-pad done when I had let it go a bit too long.Those who have their saxes regularly serviced may never have to worry about it at all.
Well that changes (almost) everything!I was wrong on the Vito (Jupiter) tenor, bought it in 2010, not 2012.
