Misc electronics All things in the battery powered microphone, mixer and speaker sphere.

⚠️ In Canada, the primary license-exempt frequency bands authorised for wireless microphones within TV broadcast spectrum are 470–608 MHz (UHF) and 174–216 MHz (VHF)

⚠️ Took a deeper look and found a caution! ⚠️
"Check the Specific Frequency Stamp. Products like this are often manufactured to blast up to a 150-meter range. Because they are powerful, you need to check the physical sticker or menu on the unit to see what exact megahertz (MHz) range it is locked into."
"Danger Zone: If the frequencies reads above 614 MHz, you run a high risk of getting severe static and audio interference from local cell towers, and you are technically operating an illegal device."

I checked and the unit is compliant but is close to the max allowed in Canada. 🎶
 
thomsax I tend to have to move about a lot playing DJ sax, down on the dance floor, mixing in the crowd, walk the tables or back of the house. I do get to just stand and deliver with many bands but I often am hired for the performance and moving about is required.

Unlike basic wireless microphones, a True Diversity system utilises two independent receiver antennas and switching circuitry. It constantly monitors both antennas and seamlessly switches to the one receiving the stronger signal. This prevents the signal dropouts caused by "dead spots" or radio wave reflections on a stage. For a moving saxophone or horn player, this is highly desirable.​

 
Thank you Vetirnari. 🙏🏼
Three years ago when I bought an EV8 and then a 2nd I wanted to connect them using UHF. I was using a Pro level wired mic at the time plugged into the EV8 and wanted better positioning of the 2nd speaker. I bought a UHF mic and a sender to connect the two speakers. No mixer just iPad into the speaker. They were cheap maybe $50.00, cannot recall the price.

I posted a thread on the other site about EV8's and received a lot of interest and very knowledgable input on EV8's and UHF. Many thought UHF was not legal back then. Learned what was permissible at that time. I did not realise that the "True diversity system" may exceed the allowable legal limit to achieve that 150-meter threshold. So good to know.

I have done gigs now with 5 speakers connected with UHF and 4 players on UHF mics. No issues and no sound tech!

I have expanded to a Mackie ProFX10GO 10-Channel Battery Powered Mixer so I can handle more players when needed. I work the mixers from my stand.
The Roland GO is perfect. Compact and easy to adjust on my stand when playing solo or with a couple of sidemen.

I have come a long way from a PA tower in a wine bar playing for two hours, noon on a Saturday. But so much new and rapidly changing electronics always something more to learn so input is always appreciated.
 
About spectrums_ Musk shared an X post from Sawyer Merritt, a prominent Tesla investor and commentator, who wrote: “AT&T CEO: Starlink Mobile won’t be able to penetrate walls. SpaceX: We’ve acquired 800 MHz spectrum, which will allow Starlink Mobile to provide better indoor coverage, including signals that can penetrate walls and other obstacles. People are underestimating Starlink Mobile.”

That frequency might toast the audience. LOL
 
Reading back through pages 1 and 2, the hardware setups from @lig and @Tonehole (running the tablet right into a battery mixer or speaker off a stand tray with zero AC cords) match how I run my violin setup outdoors.

The one gap I kept hitting with a minimal no-soundman rig was the software side feeding that speaker: tracks from different sources jumping in loudness between tunes, four seconds of dead silence at the start of an intro track, or having to hard-pause mid-song instead of a clean fade-out when a ceremony cue or crowd change happens early.

That is actually why I built SoloStage (iPad and Android) to match track loudness automatically in LUFS, trim starts and draw custom fades right on the tablet, and sync page turns to the track without a pedal or mic listening. What are @lig and @Tonehole using on the iPad right now to trigger tracks and avoid volume jumps through those battery PAs?
 
Reading back through pages 1 and 2, the hardware setups from @lig and @Tonehole (running the tablet right into a battery mixer or speaker off a stand tray with zero AC cords) match how I run my violin setup outdoors.

The one gap I kept hitting with a minimal no-soundman rig was the software side feeding that speaker: tracks from different sources jumping in loudness between tunes, four seconds of dead silence at the start of an intro track, or having to hard-pause mid-song instead of a clean fade-out when a ceremony cue or crowd change happens early.

That is actually why I built SoloStage (iPad and Android) to match track loudness automatically in LUFS, trim starts and draw custom fades right on the tablet, and sync page turns to the track without a pedal or mic listening. What are @lig and @Tonehole using on the iPad right now to trigger tracks and avoid volume jumps through those battery PAs?

My column PAs need AC so they are plugged in but my iPad/CloudVocal mic setup are battery/power bank operated so the only wire from my stand is the output to the PA(s)

Your app sounds like a nice solution to the problem. Didn't actually realize it was a problem because of how I run the tracks.

I end up exporting my tracks to .mp3 or 4 and run everything as a set list for the specific gig through Apple Music. One source, one level.

Same for when I'm taking a break. Depending upon the room I'll make a set for break time.

Didn't realize that varying output levels might be a problem but now that you mention it if you ran different sources that could be a real issue.
 
For my tracks I either download the karaoke / instrumental only version of a song or I will edit the original using vocal remover software. Then I upload to my Google Drive folder and put in my database. When performing I use a generic offline audio player that can download the tracks from Google Drive.

Matching track volume is a tricky one so this sounds like potentially a good solution.
This is the app you are referring to?
 
Yes, @Tonehole, that is the exact one! Pulling karaoke downloads and vocal-remover tracks from different places (or even YouTube rips when a client requests a specific song) is the exact headache that pushed me to build the LUFS loudness matching into it, because the mastering and compression on those are all over the map. Since you keep your tracks in Google Drive, you can also import them straight from Drive through the tablet's file picker so everything stays stored locally for offline playback on the job.
And @lig, running just one wire from the stand with the battery-powered iPad and CloudVocal into the column PA is super clean. Producing all your own tracks from one source totally explains why your levels stay consistent!
 
So far, I put in the following for backing tracks:

* set start and end points
* adjust speed and pitch (process)
* adjust loudness in LUFS (process)
* set in and out fade

process just means it actually transforms the file and potentially generates a new one, where you'll have a choice to keep both the original and the new or replace it.

And then you can synchronize page turns and annotations to the backing track as well. So if you have some note or highlight or something that you want to come up at 0:26 in the track, it'll do that for a few seconds and disappear. It makes your score nice and clean and really grabs your attention when you actually need it. I've been using it myself at my last few gigs and it's so awesome!
 
@MikeDViolin -

I'm a total audio dumbass but if your app could somehow give me the ability to take an .mp3 and somehow designate the a, b or c sections or head / chorus sections and repeat a section with a touch that would be pretty handy in the event that I want to extend a solo or have a guest performer take a chorus etc.
 
Honestly, live section repeating is not in there yet, though I have been wanting something close to that myself. Right now you can drop named cue markers in a track (like Verse, Chorus, Solo) so you can start playback from a specific spot, but once the audio is rolling it plays straight through rather than looping an A, B, or C section on demand.

Getting an ordinary MP3 to repeat a chorus smoothly without stepping on the groove is a really fun problem, though, especially compared to something MIDI-based. Would you picture it more like tapping a "repeat this section" button partway through the solo so it finishes the current chorus cleanly before jumping back to the top of the chorus, or having section buttons on screen where tapping "B" jumps right back to B on the next downbeat? That is definitely high on my list to explore next.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,058
Messages
578,303
Members
8,127
Latest member
PJ2116
Back
Top Bottom