Saxophones Pork Tales: Saxophone Repair DIY Adventures.

Life around the barn.
Tales from a pig that likes to stick his nose into everything.

Paint that S. How difficult could it be ?
1747869014621.webp


1) Search the net.
2) Find the color.
3) Order color.
4) Study task on University of YouTube, aka; For destruction by DYI presented by pro tech.
1747869824677.webp



1747869909688.webp


Do the cleaning & prep.
1747870236970.webp


Paint and cleanup / detail the edges with hard cotton swabs. Sounds easy……:confused:
1747870401847.webp


Yeah tha guy Matt makes it look easy.
Anyone remember your first experience cooking bacon crispy while still in the frying pan !
 
Old mystery shellac. Hard to tell exactly what it was made from. Synthetic hot melt of a sort ?
Hold the cup facing down to prevent getting the goo all over the cup.
1778456403649.webp


The pad work was done at different times. Some have no cardboard back. The character of the adhesive was different in melting temperature and the stringing issue.
1778456760555.webp


Best to clean everything well for the new pad installation. This time heat, wipe out cup. A bit more heat and final wipe with isopropyl did well.
1778456977484.webp
 
Customer furnished pad set. Once the cups are clean, leveled and round check the set. I was surprised only one didn’t fit. It’s not unusual to have 3 or 4 not fit.
1778457338038.webp


51.5mm would have worked. The Music Medic Pro pads are very precision and less forgiving than the other grades. Your mechanical action and tone holes need to be perfect. These are 4.6mm / .181 thick. That’s too thick for many American vintage horns. Martins require the thinnest at -4mm / .150. Cost for the grade is about 40% more not counting the booster. Add $30-$175 for boosters.
Not a recommended grade for the learning DIY.
They are comparable to Pisoni Pro pads.
With everything mechanically perfect, add 4-6 hours time getting a good seal.
1778457624690.webp
 
Customer requested to reuse the boosters. Not really any savings. A set is around $35. Took me :45 minutes to grind out the hard stainless steel rivets. Side or bullnose cutters didn’t have anything to grab onto. There’s also a chance of damage to the booster using those tools. Think potato chips.
1778459278436.webp


Don’t really need to save the backing washer. Music Medic pads have good strong cardboard backing.
1778459808330.webp

1778459948080.webp
 
The engraving was painstakingly cleaned out with a fine natural hair brush and naphtha. The verdigris, dirt and dead skin removed.
Then throughly washed in mild mix of Dawn dish soap and cold water.
Before
1778550269324.webp


And after.
1778550558828.webp

1778550610650.webp

The neck & keywork received the same steps of care. Be consistent about your work or you’ll have visual differences.
1778550792519.webp

1778550934849.webp
 
The engraving was painstakingly cleaned out with a fine natural hair brush and naphtha. The verdigris, dirt and dead skin removed.
Then throughly washed in mild mix of Dawn dish soap and cold water.
Before
View attachment 34857

And after.
View attachment 34858
View attachment 34859
The neck & keywork received the same steps of care. Be consistent about your work or you’ll have visual differences.
View attachment 34860
View attachment 34861
Beautiful work!

How does it play and sound?
 
Not sure what this bit is called ? Its function is ? It doesn’t make contact (by 0,25) with the lower C# pillar, so it’s not a support. Would be odd use for aligning the bell as it’s on the band. Right where you put the heat to solder the joint.
Regardless it fell off while cleaning. No surprise. The pink / copper look tells me it’s seen some heat. It’s crooked and off position.
1778654247670.webp

1778655109147.webp


One tiny speck of solder was all that kept it on. Not enough for 18mm of part face.
1778655572293.webp
 
Business as usual. The red area as last attached. Green area is where it goes. That needs to be good and clean.
1778656302138.webp


All old solder removed from part. Just the bottom and a smidgeon of edge.
1778656396097.webp


Flux & tin the part. I flowed a good amount of solder on the part. I don’t care to add any more upon heating.
1778657193806.webp


Mounting surface clean. A light application of flux to both sides. I then used a big fancy expensive clamp to secure the part.
I need to be careful and not damage the finish. Other than the “S” this is an “don’t touch the finish” job.
1778658016732.webp
 
In your last (clothes peg) pic, the thing just to the right (bow clamp?) looks like it is held with 2 grub screws - so it is removable without soldering? If someone did, then the bit you just put back on looks like an alignment jig to get everything back in the right place.
 
Twenty seconds and it’s done.
1778659053669.webp


Clamp off, check the work.
It’s straight and solid. Leave it alone. Yes I could go heat again and add a bit of flux to perfect the finish some. But honestly this is a one & done.
1778659479713.webp


Clean the area with baking soda & water mix to neutralize and remove any flux.
All done.
1778660006511.webp
 
In your last (clothes peg) pic, the thing just to the right (bow clamp?) looks like it is held with 2 grub screws - so it is removable without soldering? If someone did, then the bit you just put back on looks like an alignment jig to get everything back in the right place.
That’s the bow to body clamp side. If you removed the bell & bow from there. The alignment bit I just replaced is handy.
Good eye !
 
The mix was one drop paint off fat end of toothpick. Five dunks of needle in thinner that you can’t see it’s on the needle.
Final stir the paint and dunk the toothpick in. Look at the tip. No big uncontrollable blob is best. The volume on the glass shows the difference in what one dip equals.
1778271186110.webp
Day five paint check results.
None are tacky with a good press of finger pressure. All retained gloss. The hue difference is just the lighting.
1778737529345.webp


The hardness / film layer test results show why thinning is necessary.
Remember each of these three represent one dunk of the toothpick.
Left directly from container, mid is partly thinned, right fully thinned as applied.
1778738239867.webp


Fingernail press test above. Yeah, low tech but most people have fingers. No fingernails🤦‍♂️ just pick a used reed.
The left is still soft or molten inside.
Middle is reasonably hard, only a very slight indentation.
Right is hard as steel.
 
Cleaning some more hardware. Pivot screws to be exact.
When chemical cleaners fail, go mechanical. Here’s a technique that works consistently for me.
Most all the hardware on this project had Locktite 242 blue on it….and maybe some household goo stuff.
1778739658252.webp


The cleaning kit is simple.
1778739773943.webp

Block of soft wood like pine.
Scrap of 1/16” thick PVC plastic.
Vintage ice pick.
Small steel wire brush & hard toothbrush.
Not pictured. Screwdriver, fine flat jewelers file.
 
Start a hole in wood just to depth where threads start. This using the ice pick.
Using a good fitting screwdriver, run the screw in & out partial turns until bottomed into wood. The goo underneath the head is what came off.
1778740505760.webp


Still in place, use the wire brush to clean the head. Back it out a turn or three and use the toothbrush to clean underneath the head.
Lastly I dress the head slot. (These are stainless steel).
This below is the same screw as post above.
1778740922612.webp
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,064
Messages
578,464
Members
8,130
Latest member
tommyliehe
Back
Top Bottom