Saxophones Pork Tales: Saxophone Repair DIY Adventures.

Life around the barn.
Tales from a pig that likes to stick his nose into everything.

Paint that S. How difficult could it be ?
1747869014621.webp


1) Search the net.
2) Find the color.
3) Order color.
4) Study task on University of YouTube, aka; For destruction by DYI presented by pro tech.
1747869824677.webp



1747869909688.webp


Do the cleaning & prep.
1747870236970.webp


Paint and cleanup / detail the edges with hard cotton swabs. Sounds easy……:confused:
1747870401847.webp


Yeah tha guy Matt makes it look easy.
Anyone remember your first experience cooking bacon crispy while still in the frying pan !
 
Plastic sheet can be used in similar way. Be aware the results may not be as good as wood. Still this is a good way not to drop & loose the bit or chew up your fingers.
1778741227931.webp


Clean the point carefully with wire brush. Especially if the pivot is straight pin type. Don’t bend it !
1778741362428.webp


Turn it over and finish the head same as above.
1778741548669.webp
 
Look for clues when talking things apart. This is also a perfect example of the need to keep placement accurate. The reason to have a hardware caddy.
1778742125847.webp


This position has the wrong screw on both ends !
The bit didn’t clean up anyway. All this small stuff is where the time goes. Fixing all those free quick repairs from the last 70 years.
1778742375192.webp
 
Doing a “dry fit”.
This means installing a key with a pad and no shellac. A kind of pad thickness test.
1779010745819.webp


During this I also rotate a pad for best overall fit. Pads are not perfectly symmetrical in thickness. Old keywork is far from perfect.
Rotating the pad is beneficial to acquire best fit. Then note the required amount of shellac needed.
Does the pad contact the heel first or toe?? Heel being the hinge side.
Think of this like walking. As you step forward, does your heel or toe contact the ground first ??
If the action (moving key parts) is loose. I have better luck dry fitting with the action springs loaded / attached.
Age related ware without key fitting matters. If you don’t know or understand this terminology it’s time to ask.
1779011317404.webp


So… what is shellac net ?
This is just enough for the pad to bond to a cup. Over applying shellac can cause the excess to ooze out the sides of pad & cup.
Visually, well it’s a learned skill. Hard to picture.
1779013376602.webp

Net + looks like two drops more.
1779013473080.webp
 
Last edited:
During this I also rotate a pad for best overall fit. Pads are not perfectly symmetrical in thickness.
Rotating the pad is beneficial to acquire best fit.
Additional note on dry fitting. Once I have the best position. I then index mark the pad. Just a little dot at edge by key arm. This way I know exactly where to place them with shellac on.
1779063228204.webp
 
So you have a sax that requires round cork on key feet.
What do you do on Saturday night and the jobs now a rush for Monday morning delivery !!
1779151306786.webp


The answer is make it happen….
Tool time ! 👨‍🔧
The size is 7mm diameter X 5mm long. The few hollow paper drill bits I have are too small or too large. Also the finished spare needs to be from the inside diameter. The cutting edge bevel to outside.
1779152199840.webp
 
I started off with a length of 3/8”~10mm all thread stock. Mild steel that cuts fast, but is really too soft for tool use. I need it fast !
The diameter seems close enough. I’m after a final wall thickness of .040~1,03 and hopefully smooth on outside.
1779153525746.webp


On my lathe I started with drilling a center point on end. Then turned the outside down using a live center.
That didn’t go well. The outside wasn’t smooth & clear @ 7.5mm. Oh well.
Using a 17/64” drill bit (just under 7mm) I ran it in this much. The last .500 ~13mm needs to be solid for mounting in drill chuck.
1779154912091.webp


The tip I put an edge on and parted off the tool.
All was well until I attempted to drill a window port. I need a window to press the spare out of the tool.
The wall thickness is too thin @.016~ 0,39.
1779155871634.webp

1779158986808.webp
 
I managed to salvage the remaining area. Reasonable cutting tool @1600 RPM.
Note the sawdust like debris. This is from the port being too low. It’s acting like a cheese grater.
1779156268127.webp


For good repetitive clean cuts. Set the depth stop on your drill press. Just kiss the wood backer. The tool will hold an edge longer.
1779156396503.webp


1779156868990.webp


1779156953040.webp
 
Pre disassembly take detail pictures. This horn has double felts under quick F, A & G. Touch arm A & G both have tool marks. The height of these touches are intentionally set this way. Don’t realign or straighten things until you know and understand why.
1779220385731.webp

1779220574227.webp


Close but I’m also not done yet. Regulation still in process. Notice the 1/64 shims on B & A @ backbar.
1779220850493.webp

1779221510023.webp
 
So I’ve been asked to test some experimental 3D C Melody mouthpieces. I forgot to mention all my crook corks are set at 16.13mm~.635. The standard C shank size from 1920’s🤦‍♂️. All 3 showed up at tenor size 16.93(17mm)~ .666🫣
1779263842761.webp


I have a few necks to size proper. Yeah, only nine today🤪.
The fix.
Go slow and even with Teflon tape. Don’t pull hard or apply excessive tension to the tape or you will collapse the cork permanently.
Add a reasonable layer(s) and run the mouthpiece over slowly while twisting. Smooth the material down. Don’t confuse the MPC going on easily compared to sealing. The material is very slick. Sealing will be achieved long before it feels tight.
Suggestion, install the MPC half way on cork. Cover the tenon with palm of hand. Octave pip closed, cover the open chamber of MPC with your mouth and blow some pressure. You will hear or feel if it’s leaking. If leaking add a bit more. Use soapy water if you’re deaf like me. Just don’t get it in your mouth. It tastes really bad 🙄.
1779264422450.webp


The MPC test results and maker name will be posted on the C Melody thread next week here below.
C Melody Saxophones
Saxophones - C Melody Saxophones
 
Happy first anniversary to the Pork Tales blog 😃
I hope (39k+ views thank you!) this last year of posts have benefited at least one person.
Helpful ? Dunno ?
I don’t know how to add a poll / survey midway ?
Maybe @Pete Thomas can do that ?
Anything of special repair interest or importance ? Please don’t hesitate to ask ! We all get stuck occasionally. Sheep happens !
FWIW, I’m just an average mechanic who figures out how to make things work 🫣I don’t walk on water.
I also love pigs and pig jokes 🤪
 
This thread has been awesome. Ive gone through quote alot of it and it is helpful to see great workarounds to issues you've encountered while working on a wide array of saxes.

While I dont plan to repair saxes as a business, these are certainly helpful in issues I may encounter at some point and can call back to for a solution on my own current or future horns.

Plus the pig jokes and pigurines are squealy funny!
 
I don’t know how to add a poll / survey midway ?
Maybe @Pete Thomas can do that ?
Easiest at the moment is you send me Adam with the poll question and possible answers. (And how many answers allowed). How long to run the poll and whether votes are public or not. Or maybe better as a new thread that links to the blog, seeing as poll needs to be a specific question.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,064
Messages
578,464
Members
8,130
Latest member
tommyliehe
Back
Top Bottom