Tech/maintenance Old Pads On Michael White Alto

Only downside to the horn is that it doesn't have regulation screws for top and bottom stack.
Plan to replace cork for tech cork and felts. Starting with disassemble then reassemble a few times for practice.
Got cheap Zenghao pads to use. Horn is not worth much plus lots of lacquer peal red spots rust and a few dings.
 
IMG_20220105_105955.webp
IMG_20220105_110004.webp
IMG_20220105_110104.webp
 
You’re very welcome. Always glad to help out anyway I can. I sort my workbench weekly. Good luck !

if you don’t already on a micro torch you’re going to need a heat source. These hot air units work really well. Lowers the chance of smoking a pearl or pad. Units with programmable heat settings can be had for as little as $30. About $10 more than a conventional micro torch.

These things are great, I have one. They're also useful for all sorts of other things where a controllable localised heat source is required. Subject to the usual cautions about risk of fire and explosions, they're great for freeing up seized bolts on motorbikes and the like.
 
Only downside to the horn is that it doesn't have regulation screws for top and bottom stack.
Plan to replace cork for tech cork and felts. Starting with disassemble then reassemble a few times for practice.
Got cheap Zenghao pads to use. Horn is not worth much plus lots of lacquer peal red spots rust and a few dings.
Most horns don't have regulation screws.
It might be worth making a screw board. It won't take too long to make and will be useful if you do any others.
 
Only downside to the horn is that it doesn't have regulation screws for top and bottom stack.
Plan to replace cork for tech cork and felts. Starting with disassemble then reassemble a few times for practice.
Got cheap Zenghao pads to use. Horn is not worth much plus lots of lacquer peal red spots rust and a few dings.
Regulation screws, what’s that😳 ? Cheap pads burn just as well as the expensive ones. Just make sure you don’t accidentally grab one to Dunkin your tea.
The interior of the sax is worse with green and rust spot all over.
You’ll be amazed with a little elbow grease and a good brush how clean it will become. Use warm-tepid water not hot.
3C751429-E480-44D2-B56B-FEA40FE0FE95.jpeg

A08F3966-6827-4417-99B8-FA110D422F90.jpeg

CD69C178-82CC-478D-BD21-8FF5C1093250.jpeg

F605AE93-895F-407C-B6E9-1ABBB73F61AD.jpeg
B038B589-3CFE-4C6F-93ED-D068026D6EE6.jpeg
 
Regulation screws, what’s that😳 ? Cheap pads burn just as well as the expensive ones. Just make sure you don’t accidentally grab one to Dunkin your tea.

You’ll be amazed with a little elbow grease and a good brush how clean it will become. Use warm-tepid water not hot.
View attachment 19452
View attachment 19453
View attachment 19454
View attachment 19455View attachment 19456
Silver is a frustrating finish. Great when it's clean and polished but ewww when it isn't. :confused:
 
Regulation screws, what’s that😳 ? Cheap pads burn just as well as the expensive ones. Just make sure you don’t accidentally grab one to Dunkin your tea.

You’ll be amazed with a little elbow grease and a good brush how clean it will become. Use warm-tepid water not hot.
View attachment 19452
View attachment 19453
View attachment 19454
View attachment 19455View attachment 19456
Excellent work. Is this horn unlacquered?

The long handle brush, can this be bought on Ebay?

Thanks for helpful tips:thumb:
 
Should I get my carpenter mate to make something like this for me?

Saxophone Screw Block
Could do. It's just a block of plywood or mdf with holes drilled in it. Ferrees do them. If you can get a picture you can copy the layout. J90-J94 Assembly Boards
There's a diagram in the Saska repair book but the screws are better placed in the order they appear on the sax. I ended up drawing out upper and lower stacks then a section for palm keys on the upper side and so on. It's better if the layout makes sense to you! Some keys will need two holes as they can be rod screw or point screws. So you need room to add some.
 
Last edited:
Should I get my carpenter mate to make something like this for me?

Saxophone Screw Block
It’s a handy item if you’re disciplined using it. All hardware needs to be removed and stored exactly the way it was removed.
A tip @saxoclese suggests for this is simple. Take a picture and print a copy. Glue to cardboard or wood. Poke/drill holes where needed and insert the part.
B486BC9E-A126-4F79-9BB6-82BCDC9A9E6B.webp
46D9229F-D403-4604-8BE3-E467F27B9ABE.webp
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,079
Messages
578,717
Members
8,136
Latest member
peterdehelegrote
Back
Top Bottom