Accessories NUX B-6 Saxophone Wireless System

Thanks @mizmar!

I discovered today (in the manual) that the NUX-B6 'will automatically detect the best 2.4Ghz frequency channel' (out of 14). and pair with the receiver'.

It's possible that this might be the reason for the differences between rehearsals 1 & 2. For the 1st rehearsal, I was late setting up (after the guitarist). Because I'd brought along all my 'new' equipment (NUX-B6, amp, power leads, tablet _ stand, etc.) .... but had forgotten to bring along my sax :blush:! So I had to drive back home and pick it up. I'm still the but of many jokes about this 🙁.

In the 2nd rehearsal I was there early and I had already set up my NUX-B6 network by the time that the guitarist had set up his.

Over the last few days, I've learned a lot more about 'wireless transmission frequency ranges', different types of wireless systems, 2.4 Ghz.channels (number, overlap and separation), etc.

My post (above) still holds true. But I'm hoping that allowing the guitarist to set up his wireless network first, will enable the NUX-B6 to automatically select a different 2.4 Ghz. 'channel', free of interference.

Other tips, I've come across is to 'shield' (with metal) the receiver - on a lead from the amp to prevent interference.

In hindsight, it might well have been better if I'd had this kind of knowledge about the 'crowded' 2.4 Ghz. frequency band - and its 'channels' - before opting for the NUX-B6 purely on the basis of 'sound quality, reputation, ease of use, robustness, value for money, reviews, etc.'

On the topic of 'interference' between wireless systems that operate in the 2.4 Ghz. range, there are many positive posts on the NUX-B6. But also some that note that (despite the claim that the NUX-B6 'will automatically detect the best 2.4Ghz frequency channel' (out of 14). and pair with the receiver' and that 'the NUX-B6 'will never interfere with other wireless systems', there are a few posts that contradict these claims. In the sense of 'NUX-B6 almost always OK, and my preferred system for convenience, but ocassionally I needed to switch to my backup UHF wireless system.

I'll post my results.
 
NUX-B6 'will automatically detect the best 2.4Ghz frequency channel' (out of 14)
To be a little picky... Around 2.4 GHz, there are 14 channels used by WiFi/802.11 (or less depending on variant). In the same frequency range, there are 32 channels used by Bluetooth...
The channels are protocol specific and we don't seem to know the protocol used by this device... Which doesn't have to be either of those or a priority system - of which there are dozens.
There is no law saying how to divide up into channels - only that you are not allowed to output much power (roughly 1 watt)

But if they have aligned with the wifi channels.. best to keep the receiver away from a router or such! And if they do glitch, just reset one.
 
Last edited:
There's certainly a PhD in avoiding it through dynamic frequently allocation!

But, if these things can't do that - probably not - getting them to pick another channel may help.
I didn't know whether it was scanning in between or not. If it locks after determining the best frequency then a reset after everybody else is up and running may well do the trick.

No tinfoil hats on stage, though!
 
To be a little picky... Around 2.4 GHz, there are 14 channels used by WiFi/802.11 (or less depending on variant). In the same frequency range, there are 32 channels used by Bluetooth...
The channels are protocol specific and we don't seem to know the protocol used by this device... Which doesn't have to be either of those or a priority system - of which there are dozens.
There is no law saying how to divide up into channels - only that you are not allowed to output much power (roughly 1 watt)

But if they have aligned with the wifi channels.. best to keep the receiver away from a router or such! And if they do glitch, just reset one.
Hi @mizmar, yes I've read about this. The 14 channels on 2.4 Ghz seem to be used by everything including Wifi, mobile phones, microwaves and mobile garage openers! These channels overlap and are therefore very prone to interference with and by the many other devices that operate on the the same frequency range.

If I'd known about all of this beforehand, I'd have probably have opted for a different (UHF-based?) wireless system. which offers much more flexibility w.r.t. frequencies. Still, the vast majority of NUX-B6 reviews are great. Without all this info on wireless bandwidths, frequency/channel selection, I was perhaps lulled into a {false?) sense of security by the statements in the the NUX-B6 manual that:
- the signal never interferes with other wireless systems including the Wifi signal
- NUX-B6 will (automatically) detect the best channel in the 2.4 GHz. frequency band

My 'supplier' has this to say on wireless systems and the 2.4 GHz. band in particular. Based on internet reading, it seems that channels 1, 11,or 6 generally have the least overlap and interference. Unfortunately, the NUX-B6 doesn't allow manual channel selection. Only automatic.

So, again, I hope that allowing the guitarist to set up his 2.4 Ghz. wireless system first and setting up mine later will avoid interference. FWIW I've also bought a 6m (shielded) cable between my amp and my NUX-B6 receiver. So that my receiver is at least 5m away from his. Whether this will help, only time will tell.

I'm quite prepared to swap my NUX-B6 system for a more flexible and less interference-prone wireless system. But then I'd lose about $100 (50%). And if I don't need to, then I'll struggle on 🙂.
 
The 14 channels on 2.4 Ghz seem to be used by everything
It's completely irrelevant to your issues but for the record this isn't really exactly true. 2.4 GHz is known as an IMS Band not wifi... And the channels are a wifi thing. And as for "overlapping channels" etc. The engineers are staggering good at working with that.

Otherwise the notes from bax-shop are OK - except that there will never be a mass migration to 5 GHz for wifi. 5 GHz attenuates much faster, especially in buildings, which can be inconvenient.

Anyway. By all accounts it seems that a couple of these on a stage should work fine. Do your best to a/ minimize the distance between your transmitter and receiver and b/ keep other sources as far away as possible - particularly plugged in things like routers. We really know far to little about how they work to be much cleverererer
 
Last edited:
Hi @mizmar, yes I've read about this. The 14 channels on 2.4 Ghz seem to be used by everything including Wifi, mobile phones, microwaves and mobile garage openers! These channels overlap and are therefore very prone to interference with and by the many other devices that operate on the the same frequency range.

If I'd known about all of this beforehand, I'd have probably have opted for a different (UHF-based?) wireless system. which offers much more flexibility w.r.t. frequencies. Still, the vast majority of NUX-B6 reviews are great. Without all this info on wireless bandwidths, frequency/channel selection, I was perhaps lulled into a {false?) sense of security by the statements in the the NUX-B6 manual that:
- the signal never interferes with other wireless systems including the Wifi signal
- NUX-B6 will (automatically) detect the best channel in the 2.4 GHz. frequency band

My 'supplier' has this to say on wireless systems and the 2.4 GHz. band in particular. Based on internet reading, it seems that channels 1, 11,or 6 generally have the least overlap and interference. Unfortunately, the NUX-B6 doesn't allow manual channel selection. Only automatic.

So, again, I hope that allowing the guitarist to set up his 2.4 Ghz. wireless system first and setting up mine later will avoid interference. FWIW I've also bought a 6m (shielded) cable between my amp and my NUX-B6 receiver. So that my receiver is at least 5m away from his. Whether this will help, only time will tell.

I'm quite prepared to swap my NUX-B6 system for a more flexible and less interference-prone wireless system. But then I'd lose about $100 (50%). And if I don't need to, then I'll struggle on 🙂.
Going from 2.4 GHz to 5GHz or even 6GHz is trading one evil for another. Distance, even line of sight requirements (6GHz), power consumption, interference by air humidity and so on.

If the only interference you are getting is from your guitar player, maybe his setup is the culprit - I know, how am I going to talk to my child about this .... 🙂

The easy solution is still a plain old XLR cable that you route to the soundboard and you keep your receiver nearby, so you have all the control necessary.
 
It's completely irrelevant to your issues but for the record this isn't really exactly true. 2.4 GHz is known as an IMS Band not wifi... And the channels are a wifi thing. And as for "overlapping channels" etc. The engineers are staggering good at working with that.

Otherwise the notes from bax-shop are OK - except that there will never be a mass migration to 5 GHz for wifi. 5 GHz attenuates much faster, especially in buildings, which can be inconvenient.

Anyway. By all accounts it seems that a couple of these on a stage should work fine. Do your best to a/ minimize the distance between your transmitter and receiver and b/ keep other sources as far away as possible - particularly plugged in things like routers. We really know far to little about how they work to be much cleverererer
True. Up to 6 NUX wireless systems (guitar, vocal, sax, ...) can be used on-stage seem (according to the lit.) with no problems.
W.r.t. interacting with other wireless systems (for me, the guitarist) the NUX B-6 guide has 2 slightly conflicting statements:
- "each (NUX-B6 ) wireless set has a unique pairing algorithm, TX and RX automatically detect each other and configure their own ID's. The signal never interferes with other wireless (including the Wifi signal)", and "B6 will detect the best channel in the 2.4 Ghz. frequency band", but also
- "Please avoid using other wireless systems together with NUX ones, or there may be noise or interference issues"

I've just bought a 33 ft XLR (NUX Rx) to jack (Amp) lead'. About twice as long as I'd intended. But at least I can keep my NUX Rx well away from the guitarist's Tx/Rx. I'm finding out whether this has any effect tomorrow.
 
True. Up to 6 NUX wireless systems (guitar, vocal, sax, ...) can be used on-stage seem (according to the lit.) with no problems.
W.r.t. interacting with other wireless systems (for me, the guitarist) the NUX B-6 guide has 2 slightly conflicting statements:
- "each (NUX-B6 ) wireless set has a unique pairing algorithm, TX and RX automatically detect each other and configure their own ID's. The signal never interferes with other wireless (including the Wifi signal)", and "B6 will detect the best channel in the 2.4 Ghz. frequency band", but also
- "Please avoid using other wireless systems together with NUX ones, or there may be noise or interference issues"

I've just bought a 33 ft XLR (NUX Rx) to jack (Amp) lead'. About twice as long as I'd intended. But at least I can keep my NUX Rx well away from the guitarist's Tx/Rx. I'm finding out whether this has any effect tomorrow.
You can always have a jammer somewhere. It took me a few weeks to figure out that a specific type of (older) LED lightbulbs in my garage door opener had so much EMI that they jammed the garage door opener signal (I was able to open the garage door but not to close it - once the lights came on).

And that's really the crux here, you don't know what kind of "dirty" devices are around and there is no way to account or provide for them. I used to design data-center servers and EMI containment was a major part of the compliance testing but out there in the wild ...
 
I'm.dead curious as to how the radio works on this. It's very hard to find out.
I have found this, a FCC type qualification:

Probably. Given that NUX is a subsidiary of Cherub Technology Co. It's the guitar part but probably the same radio back end
There is a photo of the radio chip set - not my strong point to read those entrails.

It doesn't discuss the protocol, just the radio
... And, by the way - not that it matters - 22 channels
 
Last edited:
The continuing story ....

The guitarist and I had another 'moment of truth' this morning and (just as in my 1st rehearsal with the NUX B-6) everything went fine. No noise and no interference between our 2 wireless systems 🙂. So absolutely no reason to swap my NUX B-6 for something else.

I did have a long XLR (Rx) lead to my jack (amp) input though I'm not sure whether that helped much. Given the range of our wireless systems (20-30 m), probably not. My guitarist dismissed the possible effect. But I found it much more convenient to have my Rx 'within reach' rather than being fixed on my amp (buried behind the bass player). Just in case I should ever need to reset the connection.

The guitarist had also been doing some experiments. His suggestion (for me and for himself) was to first turn on the Tx (in my case the mic) and only afterwards the Rx. I assume that the Tx selects the optimal 2.4 Ghz 'channel'. The 'Tx/Rx order' was (for me) unclear in the NUX-B6 guide. So I'm thankful to our guitarist for figuring this out.

Today, I let him set up first (Tx tand hen Rx) and test his wireless connection with mine turned off. His connection worked fine. Then I repeated the process with my NUX-B (1st Tx and then Rx) and both his and my connections still worked fine together.

I have no idea how the NUX-B6 TX-Rx (or his) 'pairing algorithms - including automatic channel selection - work! I took a quick look at his wireless system and I'm pretty sure that it's a Yuer TR-U1. Later versions operate on 5.8 GHz. He claims that (just as with the NUX-B6) his channel selection is 'automatic'. However the 'blurb' on his wireless system describes 'optional' manual channel selection (from 4). He's probably never had to look into - or do - this. Up until now, I've read anything about which channels might be selected. On his or my wireless systems.

I suspect that (never having previously had to 'compete' with other 2.4 GHz. wireless systems) my guitarist's wireless system just 'defaults' to channel 1. Though (according to the blurb, he could manually choose a different channel). But I'm just pleased that we don't interfere with each other🙂.

So my suspicion is that by allowing him to set up first, his wireless system (by default) chooses channel 1. Setting up 2nd, the c4 probably (and automatically) chooses a different channel (6, 11 ?) with no overlap and no interference. If I set up first, the NUX-B6 will choose the first available (interference- and noise-free) channel: channel 1. If my guitarist sets up later, his wireless connection will (also) default to channel 1. Hence the interference on our 2nd rehearsal.

FWIW, my guitarist's wireless setup allows a (manual ?) selection between 4 channels (though he claims that the selection is automatic!), The NUX-B6 automatically selects between 6 channels. No manual channel selection is possible. From what I've read, only 3 2.4 Ghz channels( 1, 6 and 11) have no overlap and optimal separation.

I'm going into all this stuff in some detail. To give some positive feedback (with my sincere thanks!) to all those who have replied to this thread so far. And who have helped me learn ( with vast knowledge and practical experience!) so much more about playing with a sax mic in a band. And especially about the NUX-B6!

Thanks to your tips, my initial NUX-B6 experience has had a 'happy ending' 🙂.

I've learned so much up until now in this thread!

I hope that what we've discovered together might help future sax players who are considering the NUX-B6.

In fact, I'll contact the mods to ask whether it might be worthwhile 'merging' some recent threads on Sax mics. Or at least creating a post with links to relevant (and recent threads).

Again, my thanks to you all for your patience, your active involvement and all your suggestions and tips which have really, truly helped me (and my guitarist!) to where we are now. Playing together on 2.4 GHz. wireless systems in perfect harmony🙂;

Mike
 
Good info, Mike.
Kind of what I suspected but it's good to see somebody actually do the experimentation and confirm everything including a solution.
I know my Shure BX14 has a number of channels available but you need to manually match the transmitter and receiver and also select the channel, which can be a bit cumbersome.
I'm glad everything worked out for you!
 
From what I've read, only 3 2.4 Ghz channels( 1, 6 and 11) have no overlap and optimal separation
Again, the wifi/802.11 channel numbering almost certainly has no bearing on this.

I'm also sceptical about "automatic channel selection" unless the Tx has a hidden Rx and the Rx has a hidden Tx... to be able to negotiate. But I remain ignorant of what protocols your device is using.

Still. Good you have a ritual to set things up and hope that proves reliability repeatable.
 
So, in this context...

Place the guitarist in a Faraday Cage?
Well, that solves that mystery

1000001773.webp
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,063
Messages
578,429
Members
8,129
Latest member
Bartman
Back
Top Bottom