Tech/maintenance New neck cork and/or add a piece on neck?

thomsax

Well-Known Member
Messages
7,428
Location
Sweden
I need a new neck cork. I play an older Martin and a rather modern mouthpiece. The I.D. of mouthpice bore is c 16,5 mm, the O.D, of the neck is c 14,0 mm and c 30 mm down the cork is where I'm in tune. So it's tight. A 2 mm thick cork and there is less than 1 mm left after sading it cylindrical. Another thing I would like to point out is to not push too much if you are sanding the cork and using a bench peg. You can see a little flair on the tip and that's made when the neck cork was sand down. It's a 1938 Martin Handcraft so many mew neck corks over the years. No rings on these old saxes. Add a piece on the neck gives me more flexibility when it comes tunning. The old cork is too long c 50 mm. I just need 35 mm. Is it more than me who have problems like this? New sax or/and new mouthpiece.


20250802_124422.webp


20250802_125551.webp
 
I have sterling silver or brass resonators/reflectors with washer and screw on the back. I have medium oversized and fully oversized. I like these resonators/reflectors because they .....

..... can be used over and over.
..... holds the pad flat.
..... less (no) plating problems.
..... gives my Martin saxes a bigger sound. (low keyheights on Martin so they sing better with oversized resonators/reflectors.

I'm right now doing some minor work on my Martin HC 1938. New neck cork, cleaning and oiling. Just one pad that was rotten, high F. The sterling silver resonator/reflector is intact. No plating or corrosion problem.

20250803_143614.webp
Just warmed the key cup so the pad came out. Cleaned the key cup as well.
20250803_144501.webp
 
I had to remove the rivet on another pad. Same type pad as the earlier one. 26/38 was ok. 27/32 was a little bit too big, so it had to be 26/32. I use a pad iron, It's all there; cleaned key, pad, reflector washer and screw.
20250803_150150.webp

Warm the key cup and rub some shellack and put in the pad. I like shellack because it's a little bit more forgiving. And so is the alcohol lamp as well.
20250803_150842.webp
 
And here is the new pad with the old reflector. The key and pad was cooled down a little bit before reassemble. After reassamble I warmed up a pad iron and placed it between the tonehole and pad and pressed a little bit so the pad was floating out. The pad had to be burning in. I put a wedge under the key foot to give it some extra pressure.
20250803_151151.webp

This is very old school. A slow way to work .
 
I need a new neck cork. I play an older Martin and a rather modern mouthpiece. The I.D. of mouthpice bore is c 16,5 mm, the O.D, of the neck is c 14,0 mm and c 30 mm down the cork is where I'm in tune. So it's tight. A 2 mm thick cork and there is less than 1 mm left after sading it cylindrical. Another thing I would like to point out is to not push too much if you are sanding the cork and using a bench peg. You can see a little flair on the tip and that's made when the neck cork was sand down. It's a 1938 Martin Handcraft so many mew neck corks over the years. No rings on these old saxes. Add a piece on the neck gives me more flexibility when it comes tunning. The old cork is too long c 50 mm. I just need 35 mm. Is it more than me who have problems like this? New sax or/and new mouthpiece.


View attachment 29736

View attachment 29737
It's a matter of how you do it. I out a bevel on the cork where it starts to facilitate the overlap and then I start with sanding just the bulge after cutting off the excess.

Only then I start sanding down the rest of the cork to fit the mouthpiece. I usually put a little bevel on the tip to make it easier to slide the MPC on but I always make sure that I have enough "friction", i.e. it is a rather tight fit and then use the mouthpiece to compress the last little bit of the cork by rotating it in the direction of how the cork was mounted. I never go the opposite way, that could damage the "seam". So my cork always looks like it has a little bit of a step but the MPC is sitting very firm (I hate when a mouthpiece wobbles on the neck). But with a bit of grease, it is easy to mount and adjust the mouthpiece and if I find I need to push it on a bit more, it's never been an issue, the same for pulling out. Cork is an amazing material unless you get some bad quailty.
 
I need a new neck cork. I play an older Martin and a rather modern mouthpiece. The I.D. of mouthpice bore is c 16,5 mm, the O.D, of the neck is c 14,0 mm and c 30 mm down the cork is where I'm in tune. So it's tight. A 2 mm thick cork and there is less than 1 mm left after sading it cylindrical. Another thing I would like to point out is to not push too much if you are sanding the cork and using a bench peg. You can see a little flair on the tip and that's made when the neck cork was sand down. It's a 1938 Martin Handcraft so many mew neck corks over the years. No rings on these old saxes. Add a piece on the neck gives me more flexibility when it comes tunning. The old cork is too long c 50 mm. I just need 35 mm. Is it more than me who have problems like this? New sax or/and new mouthpiece.


View attachment 29736

View attachment 29737
The radius of that flair looks like it could have been intentional and original. I don’t know this brand well enough to know whether it is. Some contemporary horns have a slight flare as well.

@PigSquealer Whaddaya think?
 
It's a matter of how you do it. I out a bevel on the cork where it starts to facilitate the overlap and then I start with sanding just the bulge after cutting off the excess.

Only then I start sanding down the rest of the cork to fit the mouthpiece. I usually put a little bevel on the tip to make it easier to slide the MPC on but I always make sure that I have enough "friction", i.e. it is a rather tight fit and then use the mouthpiece to compress the last little bit of the cork by rotating it in the direction of how the cork was mounted. I never go the opposite way, that could damage the "seam". So my cork always looks like it has a little bit of a step but the MPC is sitting very firm (I hate when a mouthpiece wobbles on the neck). But with a bit of grease, it is easy to mount and adjust the mouthpiece and if I find I need to push it on a bit more, it's never been an issue, the same for pulling out. Cork is an amazing material unless you get some bad quailty.
Thanks. Good tips.
 
The radius of that flair looks like it could have been intentional and original. I don’t know this brand well enough to know whether it is. Some contemporary horns have a slight flare as well.

@PigSquealer Whaddaya think?
I think you're right. Not a damge when I take a closer look.
 
I took a picture of my tenor necks when I was replacing a new neck cork to the Martin HC 1938 I had a closer look at the three other tenor necks/saxes I use. From left to right:

1. "The Martin Magna" 1959: Weight 235 g, total length (Inside from tip to tenon end/ wo tenon) 250 mm/240 mm, I.D. tip 13 mm, I.D. tenon 26 mm.
2. "New King" (Keilwerth 1968): Weight 166 g, total length (Inside from tip to tenon end/ wo tenon) 240 mm/210 mm, I.D. tip 12 mm, I.D. tenon 26 mm.
3. Martin Handcraft 1938: Weight 141 g, total length (Inside from tip to tenon end/ wo tenon) 230 mm/190 mm, I.D. tip 13 mm, I.D. tenon 26 mm.

Martin made some changes on the neck/tube over the years. From what I can see the longer end of the neck was not tapered on the Magna. Otherwise It's more the shape of the neck that are diffent. "The Magna" on the "New King" are better for to play standing. The HC is better to play sitting. Big Band era sax?

The Magna neck is a heavy one. More stuff on this neck. The Martin combined alto and tenor necks are heavier necks. Mass?

This compare is made with primitive "tools". Just wasting my time and waiting for the rain to stop.


IMG_20250806_104659.webp
 
I'm not sure what the issue is. As I read it (16.5 MP ID - 14 neck OD)/2 = 1.25 mm thickness. Plenty to work with.

If you want to put a shorter cork, put a shorter cork. You'll need to clean off the old cement and polish the area where the cork isn't there any more.

My alto of about the same age (Martin HC committee "1") has a little flare like that (not flair, that's a felt tip pen). I always figured it was something someone did following some theory about "smoothing the air flow" or such. It would be interesting for if someone with more extensive experience with Martins of this generation could comment; was this in fact a factory feature?
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,059
Messages
578,315
Members
8,127
Latest member
PJ2116
Back
Top Bottom