See my previous post, then tell Ken Beason he doesn’t know what he’s talking about.All toneholes can be leveled and properly installed pads do not require clamps. Next question. 😉
See my previous post, then tell Ken Beason he doesn’t know what he’s talking about.All toneholes can be leveled and properly installed pads do not require clamps. Next question. 😉
See my previous post, then tell Ken Beason he doesn’t know what he’s talking about.
Yep, using the clamps I already had (free) was much cheaper than a major rebuild of the tone hole chimney. In any case, that horn is long gone. Haven't use any clamps since.I imagine that Ken would be up to the task of rebuilding the tone hole chimney if you agreed that it was worth it.
Sad to see when that happens - filing a tone hole in an effort to flatten it, only to fail with not enough tone hole left to fix it.
Key Leaves and key clamps are apples and orangesWe've all had the G# key stick.... some people clamp their key's shut
Postie will do it.A rubber band will clamp a cup closed. They're aso free if you follow a post...was going to put man. However some postmen are women. Mail deliverer seems so inhuman. Black and white cat not withstanding.
See my previous post, then tell Ken Beason he doesn’t know what he’s talking about.
Not recommended for a silver horn ...A rubber band will clamp a cup closed.
I agree totally, using key clamps in that situation should not be an option.OK, so, not enough 'meat' left on the toneholes?
Three options, just off the top of my head:
All toneholes can be leveled and properly installed pads do not require clamps.
I took jbt's post to include provison of level tonehole whether it be by filing, manipulating the base, rebuilding, or some method hitherto unknown to mankind. I doubt any tech (however good or bad) would recommend to fix a grossly worn and unlevel (down to 1mm of chimney!) by using keyclamps except asa very emergency short term bodge.One of the best techs in the US told me one of mine couldn’t, not enough material left. Sure enough, part of the hole rose barely a mm above the body.
One of those sticky yellow things?Postie will do it.
Well the horn continued to play fine for another 15 years for me. Next time I’ll get in my time machine and avoid the clamps so you lot are happy.I agree totally, using key clamps in that situation should not be an option.
I took jbt's post to include provison of level tonehole whether it be by filing, manipulating the base, rebuilding, or some method hitherto unknown to mankind. I doubt any tech (however good or bad) would recommend to fix a grossly worn and unlevel (down to 1mm of chimney!) by using keyclamps except asa very emergency short term bodge.
Well the horn continued to play fine for another 15 years for me.
No need to, avoiding the key clamps is not what makes me happy🙂Next time I’ll get in my time machine and avoid the clamps so you lot are happy.
Doesn’t sound like it. I just keep reading every other solution under the sun to avoid clamps. I only did what my tech told me, and it worked. We can second guess him indefinitely, but what’s done is done, and the results speak for themselves.I'm not disputing that. But I bet it was the tech's skill rather than the key clamps. I would think a further otion to fix that issue could have been very judicious bending of the key cup and/or pad floating/shims. I'm sure that could last very well when done by the right tech.
No need to, avoiding the key clamps is not what makes me happy🙂
If you have a chronically stick G#, clean the pad and the edges of the tonehole.A bit late to this discussion. I really like Key Leaves, they really stop mu G sharp sticking. One problem though is that the strap between the 2 wedges snapped at one of the holes, so I had to use some gorilla tap to reattached (Itried to make a new hole with a hot neddle but it just snapped again)
