Saxophones Holton tenor Elkorn year manufacture

This is what happens when there’s no or insufficient interior stuffing.
and yes just like the catalog picture above. The 1924 had a Mercedes style guard.
1703627758758.webp

1703627993807.webp


using the champagne cork is better than nothing. Remove the thumb screw and the Lyra screw. Tape those to a piece of paper and stick it in the bell.
1703628440589.webp
 
This is what happens when there’s no or insufficient interior stuffing.
and yes just like the catalog picture above. The 1924 had a Mercedes style guard.
View attachment 24941
View attachment 24942

using the champagne cork is better than nothing. Remove the thumb screw and the Lyra screw. Tape those to a piece of paper and stick it in the bell.
View attachment 24943
I recently bought the horn and was told it needed new felts and corks and regulating it cost me 300 pounds off eBay as it looked nice and clean I took a chance . I took it to my tech as it would not play until work completed and he told me it also needs a repad. This will cost me another 300 pounds and he is a friend so doing it cheap. Therefore I have the option of sending back to seller and getting my 300 purchase price back or putting another 300 into it for a repad so in total it will cost me 600 pounds As it would not play on receiving it I have not heard tone etc so that my predicament. How does it sound in compared with a Conn tenor ? As Iv had one off the transitional models and a Non rolled tone hole 10 m also.
Regards
 
Well if it arrived at your doorstep in one piece. The seller did a good job on the shipping.
£300 ($381 usd) is a fuzz high but not awful.
Just consider it a little bit of a premium for one in very good condition. I’ve looked up the listing and reviewed the pictures. Yes it is in very nice condition. A few little dimples in the back of body & bow. No big deal.
Doesn’t appear to be damaged over its lifetime and very low mileage unit at that. There’s no ware in the strap ring. The one spot plating missing on bowfin is from case. So yes, maybe a £100 /$127 premium was worth it.
I don’t see these as common in your region.

The few pictures of the pads that I can see. Well those look like a mixed bag of beans. Originals for that year were tan or white with a single stitch.
Yes, a repad on this is good advice. Worth it ? On a chance you don’t like it you may break even or lose a little bit. £600 /$763 is not out of line for a quality vintage tenor.

Sound comparison to any Conn. I’ve attached two YouTube videos
for your ears. Two different levels of playing. Two different models / years.
Pads make a difference in sound. Pads with rivets will sound differently than pads with rivets and the back filled with shellac. Flat metal boosters will sound different than domes. As you make each incremental change from a plain pad up ( a single stitch in the middle of the pad “plain”), The sound definitely changes on these. The first video I would say is riveted pads. No backfill. Mr. McLean on the RW model below most likely has domed boosters.

1926 tenor without front F like yours.
View: https://youtu.be/PsXp1a0MxIA?si=KldGL77wAblHsjFD


1930 Rudy Wiedoeft model
View: https://youtu.be/jFeyzhbpQz0?si=teYJUnVGPCGGSzJ5


When your tech says it needs new hing rods or lots of key fitting. Just laugh and think about it for a minute. How could it need these parts with no signs of use ?
Holton‘s we’re set up with loose tolerances. Heavy body grease and pillow pads. Tech of the era.
If the tech files the tone holes flat you will see missing silver around the rim of each one. Next will be swagg/swedge marks on all the tubes.
 
Last edited:
Well if it arrived at your doorstep in one piece. The seller did a good job on the shipping.
£300 ($381 usd) is a fuzz high but not awful.
Just consider it a little bit of a premium for one in very good condition. I’ve looked up the listing and reviewed the pictures. Yes it is in very nice condition. A few little dimples in the back of body & bow. No big deal.
Doesn’t appear to be damaged over its lifetime and very low mileage unit at that. There’s no ware in the strap ring. The one spot plating missing on bowfin is from case. So yes, maybe a £100 /$127 premium was worth it.
I don’t see these as common in your region.

The few pictures of the pads that I can see. Well those look like a mixed bag of beans. Originals for that year were tan or white with a single stitch.
Yes, a repad on this is good advice. Worth it ? On a chance you don’t like it you may break even or lose a little bit. £600 /$763 is not out of line for a quality vintage tenor.

Sound comparison to any Conn. I’ve attached two YouTube videos
for your ears. Two different levels of playing. Two different models / years.
Pads make a difference in sound. Pads with rivets will sound differently than pads with rivets and the back filled with shellac. Flat metal boosters will sound different than domes. As you make each incremental change from a plain pad up ( a single stitch in the middle of the pad “plain”), The sound definitely changes on these. The first video I would say is riveted pads. No backfill. Mr. McLean on the RW model below most likely has domed boosters.

1926 tenor without front F like yours.
View: https://youtu.be/PsXp1a0MxIA?si=KldGL77wAblHsjFD


1930 Rudy Wiedoeft model
View: https://youtu.be/jFeyzhbpQz0?si=teYJUnVGPCGGSzJ5


When your tech says it needs new hing rods or lots of key fitting. Just laugh and think about it for a minute. How could it need these parts with no signs of use ?
Holton‘s we’re set up with loose tolerances. Heavy body grease and pillow pads. Tech of the era.
If the tech files the tone holes flat you will see missing silver around the rim of each one. Next will be swagg/swedge marks on all the tubes.
Thank you again for a thorough detailed response . For the type of slow jazz ballads I play and like looks a perfect match .
Regards.
 
Well if it arrived at your doorstep in one piece. The seller did a good job on the shipping.
£300 ($381 usd) is a fuzz high but not awful.
Just consider it a little bit of a premium for one in very good condition. I’ve looked up the listing and reviewed the pictures. Yes it is in very nice condition. A few little dimples in the back of body & bow. No big deal.
Doesn’t appear to be damaged over its lifetime and very low mileage unit at that. There’s no ware in the strap ring. The one spot plating missing on bowfin is from case. So yes, maybe a £100 /$127 premium was worth it.
I don’t see these as common in your region.

The few pictures of the pads that I can see. Well those look like a mixed bag of beans. Originals for that year were tan or white with a single stitch.
Yes, a repad on this is good advice. Worth it ? On a chance you don’t like it you may break even or lose a little bit. £600 /$763 is not out of line for a quality vintage tenor.

Sound comparison to any Conn. I’ve attached two YouTube videos
for your ears. Two different levels of playing. Two different models / years.
Pads make a difference in sound. Pads with rivets will sound differently than pads with rivets and the back filled with shellac. Flat metal boosters will sound different than domes. As you make each incremental change from a plain pad up ( a single stitch in the middle of the pad “plain”), The sound definitely changes on these. The first video I would say is riveted pads. No backfill. Mr. McLean on the RW model below most likely has domed boosters.

1926 tenor without front F like yours.
View: https://youtu.be/PsXp1a0MxIA?si=KldGL77wAblHsjFD


1930 Rudy Wiedoeft model
View: https://youtu.be/jFeyzhbpQz0?si=teYJUnVGPCGGSzJ5


When your tech says it needs new hing rods or lots of key fitting. Just laugh and think about it for a minute. How could it need these parts with no signs of use ?
Holton‘s we’re set up with loose tolerances. Heavy body grease and pillow pads. Tech of the era.
If the tech files the tone holes flat you will see missing silver around the rim of each one. Next will be swagg/swedge marks on all the tubes.
Evening , spoke with tech today he has put nickel resonators on the pads , said it looks beautiful full overhaul pads , felt and corks. Picking up weekend so hopefully will sound glorious.
 
Picking it up Saturday I will update you
Well it’s home , beautiful , booming deep vintage sound with a mix of smooth silky velvet, Very happy sound wise on par with my Conn 1932 transitional I used to own. Very happy plays well with an Otto link sig slant hard rubber and equally as well with my metal Otto link tone master 5 opening also going to try my brilhart Ebolin tomorrow.
 
Well it’s home , beautiful , booming deep vintage sound with a mix of smooth silky velvet, Very happy sound wise on par with my Conn 1932 transitional I used to own. Very happy plays well with an Otto link sig slant hard rubber and equally as well with my metal Otto link tone master 5 opening also going to try my brilhart Ebolin tomorrow.
Do you feel those two videos fairly represent what you are experiencing?
 
Do you feel those two videos fairly represent what you are experiencing?
I wish I sounded like that I’m still bedding it in well trying a few times it’s got stuck in high octave , picked it up tried to blow but it was like the mouthpiece blocked I think one of the keys were open not sure had a fiddle and it blew fine , so getting used to it , I going to look at a basic Otto link mp my metal piece don’t suit it really.
 
Like a new pair of shoes. It takes a while to break them in and be comfortable. Your experience notes will help another member down the road.
Yes that’s exactly what I thought , also due to the vintage keys and layout extra trill side keys etc I might be touching one slightly opening causing the restricted air flow. Who knows it does have a great tone though
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,071
Messages
578,539
Members
8,132
Latest member
LouisJR
Back
Top Bottom