Accessories Another wall mounting thread

greenstripe

Member
Messages
950
Location
UK
I've ordered a couple of wall mounts for my saxophones from Bax (who I believe are based in the Netherlands). I've gone for the König & Meyer 44240 believe it or not virtually no one seems to stock this stand model in the UK, or anywhere for that matter -go figure!

The stand is obviously designed for shop usage with slat walls, but there is an adaptor for using on conventional wall mounting which I've also purchased.

I wanted a mount where the saxophone bell faces the wall as I don't have much wall space available in my music room and also I like to keep a pillow case over my saxophones when I'm not using them to keep dust off them.

Does anyone have experience with this model of stand and or buying from Bax and shipping to UK? I always worry about buying from the mainland post Brexit


44240-000-55.webp
 
I can only comment on their pre-brexit service, I bought an alto case which coincidentally is in the yard sale because my only remaining alto has left hand bell keys. The item was accurately described, packed well and despatched promptly.

Maybe drop them an email?
 
Looks pretty flimsy to me, with that thin strip cantilevered out from the wall with its weak dimension in the loaded direction, then hanging from that wee little sheet metal cantilevered bracket, holding your $3000 sax with ONE SCREW into the wall.
 
We'll see when and if they turn up or I get hit with some kind of import duties -fingers crossed.

@turf3

K&M kit is generally pretty good quality and a well respected brand, but I will reserve judgement untill I have the stands in my hands. The stand is designed to hook in to slatted walls in shops, you're probably looking at the single screw hole that is used to lock it in to the adaptor. The adaptor itself is fitted to the wall with 3 screws. See below:
44060-000-55.webp
 
OK, so now you're hoping that the little lip on the plastic piece that holds the bracket tongue doesn't break off, or that the tongue doesn't bend enough to come out of the plastic part.

Looks mighty hinky to me.
 
I put my tenor and bari saxes on the wall of my music room, and I was some what concerned about havind a (almost) 6 kg bari sax on the wall. I got the stands by Home page And I must say that they are very sturdy and hold my saxes very well.
But they are side-facing holders, so perhaps not suited for your purpose.
Bari-en-tenor-aan-muur-uitsnede.webp
 
I don't cover them....
Before I had these wall stands, they just say on a floor stand.
I guess I just blow off the dust when I am playing them ;-)
 
I'm not wanting to display my saxophones but can appreciate why people might -they're attractive objects.

I don't like the idea of putting my saxophones away in their cases straight after playing - I prefer to give them a chance to dry out (after cleaning). Also I am seeking to make things as convenient as possible to maximise my practice time.
 
OK, so now you're hoping that the little lip on the plastic piece that holds the bracket tongue doesn't break off, or that the tongue doesn't bend enough to come out of the plastic part.

Looks mighty hinky to me.
Or maybe the top of the stands plate slides up and into a slot at the top of the mounting plate, the rest if the bracket clicks into the square of the mountain plate and the little screw just insures it doesn't get pulled out when removing the horn? Lots of plastic taking the weight, stress and strain. Could well be up to K&Ms normal engineering standards.

I look forward to hearing how it actually works
 
Last edited:
Here is a section of the mounting instructions for the adaptor plate to avoid speculation (shown with a different attachment from the saxophone holder)

Also forgot to add "Material Adapter: Polyamid, fiber glass reinforced, black" so should be sturdy



Screenshot 2022-03-08 211143.png
 
Last edited:
My issue is that it’s likely to be mounted pretty high. At least in comparison to a floor stand. Any failure, be it mechanical or human error will result in severe damage. Falls from floor stands can be pretty terrible…add four feet and it’s catastrophic. Im of the belief that there are safer alternatives. This is especially the case with quite valuable horns. Maybe Im paranoid but I have had some close calls.
 
I'm also not keen on the horns sticking way out into the room. One miscalculation or one flowing caftan could cause you to snag the back end of the horn and flip it off onto the floor.

I'm with Phil there, in fact if a floor stand seems to position the horn higher than needed I modify it. As far as I'm concerned the right height for a floor stand to hold a horn is with the bottom of the bow just a few mm above the floor. (Obviously a stand you use for playing the horn is different.)
 
Instinctively I get what @Phil and @turf3 say (although I don't see much caftan action in my household). The rational me, though, is curious about how often falls from wall mounts actually happen. @Jules when you had 200+ wall mounted saxes in sax.co.uk Crowborough, did you have many horns knocked off the wall?
 
The stands arrived yesterday - didn't have time to put them up until this evening:

I've had a rethink about how they would fit in the space - they cannot actually be fitted with the saxophone completely facing the wall as the neck would hit the wall in this position. Here are the adaptor plates for regular walls:

IMG_20220311_173634.webp


And saxophones in situ:

IMG_20220311_175716.webp


The stands are underslung so I can use my pillowcases:

IMG_20220311_175626.webp
 
And for those that are interested I've just received some new cotton pillow cases from Amazon that are described as 'kingsize' this means that they are longer but not wider and are perfect for the tenor and the alto:

 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,079
Messages
578,702
Members
8,136
Latest member
peterdehelegrote
Back
Top Bottom