Tech/maintenance Replacing corks and felts; basics?

Ahhhhhhhhhh!¡!!!!!!

all was working fine, then a couple of days ago it became next to impossible to close G, A and B - as judged by the leak light and the basically horrible and unstable sound (even for me) issuing forth.

Then only proximate cause I can think of is the cold (-10 to -15⁰ here) / low humidity snap causing some manly shrinkage? Does key work suffer like that also?

Can this be symptomatic of naff pads?

Back on the Alto till I get this sorted, which is ok as well.
 
Last edited:
It won't be the keywork. At worst it'll get sluggish at low temperatures due to the oil/grease congealing - and at the temperature where the keys actually bind due to contraction, you probably wouldn't want to be playing a sax anyway.

Could be naff pads. Some Yamaha Vitos seem to be fitted with very soft, squidgy pads - and these seem to soak up any moisture in the air. It's also quite likely that there's hardly any shellac holding them in place. So you have relatively unstable pads, unstably fitted. It's not wonderful.
 
Well, I replaced the problem pads with those in the musicmedic goody bag.

It didn't go brilliantly nor badly.
The seemed a mm or so thicker than those fitted and the keys didn't close so well as the hinge side made contact before the off side, even with minimum glue. Exactly the opposite of the original problem!!.After some reading etc. I resorted to; heating, prodding and pokeing... And lightly clamping them overnight... And now it's all working. Just.

So I'm thinking of ordering a set of YTS 23 pads - shabby was is a Yamaha Vito - as there are, anyway, some I'd like to replace that weren't in the goody bag anyway.

Something for the new year.

 
Last edited:
Well, the premium deluxe set arrived from windplus (as per this post) and, after suitable procrastination, I've actually replaced everything from A down. The top stak can sit with musicmedic pads for now.

Quite an interesting mixture of glue in the old pads; some transparent (hot glue?) Some bile-yellow...

And its sounds fab! Maybe best it's ever sounded. I'm a bit surprised because it didn't seem in bad shape and, doing DIY, I rarely leave things better then I found them.
All the way down to B, anyway; which shows a glimmer of leak. A little fettling required.
 
Last edited:
All the way down to B, anyway; which shows a glimmer of leak.
So I checked again last night, in ta' midnight hour.
B and B♭ both had identical leaks; a faint crescent of light in the same place, on the key cap arm side. I take this as evidence of the bell having taken a knock and being a little rotated? But I think I knew that.
If a little light overnight clamping doesn't work, I suppose refitting with a drop extra glue should suffice.

And, for the record:
- hot glue just because it's cheap and available and less scary
- MusicMedic medium oil on rods because that's what was in the box
- teflon grease on the point screws because... pushbike
 
Last edited:
I suppose refitting with a drop extra glue should suffice.
A stint in a walk-in storage room, leak light, glue gun, butane torche; has left low C too B♭ considerably more solid and litte feeling left in my fingertips.

that'll do for now. Just let things settle down till the next bit of fixings comes flying off....
 
I'll let this thread slip below the waterline for now. But, just to say; scruffy sax has never sounded so good or played as well as it does now; including after each visit to local techs who were a bit "your not from round these parts and this isn't a Selma, so I'll do what I can while wearing lead lined rubber gloves and a respirator" before covid and in Trøndersk dialekt.

For anyone thinking of going down the DIY route; really read the advice and musings from folks here - it's invaluable. I'd like to give the kind of thanks that come from a really good practice session where the horn cooperated all the way, to everyone who helped in this and contributed to other technical threads. :cheers:
 
Last edited:
So I checked again last night, in ta' midnight hour.
B and B♭ both had identical leaks; a faint crescent of light in the same place, on the key cap arm side. I take this as evidence of the bell having taken a knock and being a little rotated? But I think I knew that.
The bell is usually "tilted" to one side or the other. It seldom gets rotated unless the bow to body connection has come loose. My remedy: facing the saxophone looking at the bell see which side of the low B and Bb pads touch first. If the fronts of the pads touch first, hold the body of the sax firmly and "slap" the right side of the bell. If the backs of the pads touch first "slap" or "karate chop" the left side of the bell. Check with a leak light after each "hit". Repeat if the bell has farther to go, and if you've gone too far, do it the opposite direction
 
I did refit the B and B♭ pads. I had been very sparing with the glue in the first pass. A little gentle/brutal realignment of the bell would probably have worked. Let's see how it settles down.
 
Last edited:
I'll let this thread slip below the waterline
Despite which, just for the record, I've completely finished installing all the windpluss pads, from octave pip to big old Bb; even swapped out the MusicMedic ones. So they're all the same make, age, glue (I found one pad with red snot glue in addition to transparent or yellow snot under other pads) etc. Lots of trips to a dark room, checking etc ... It's lovely.

So much for
at least what I can without removing keywork,
 
It's lovely.
And, as such, following this discussion, we bring the era of

IMG_20230314_142927532.jpg


To an end

IMG_20230314_143328732.jpg


I'm sure it'll bring another step change in tone production 😉
 
You can buy yamaha "pearls". To have MOP installed .... Better to glue and solder in coins or brass touches. Yamaha's pearls are good. Keilwerths from the 60's are terrible. Bad plastic.
 
The bell is usually "tilted" to one side or the other. It seldom gets rotated unless the bow to body connection has come loose. My remedy: facing the saxophone looking at the bell see which side of the low B and Bb pads touch first. If the fronts of the pads touch first, hold the body of the sax firmly and "slap" the right side of the bell. If the backs of the pads touch first "slap" or "karate chop" the left side of the bell. Check with a leak light after each "hit". Repeat if the bell has farther to go, and if you've gone too far, do it the opposite direction
This is why the bell to bow and bow to tube joints really ought to be soldered. Also the joints of the bell brace. Even most modern horns have a bell brace that is plenty stiff back to front but weak in resisting side to side motion. I think the best mechanical design of a bell brace is the Conn bari and bass "X" brace. In fact on my Noblet/Beaugnier bass, which had a REAL hinky brace design, where the whole bell could be moved from side to side at least 5 mm with just light hand pressure, I not only soldered down all the screw joints on the original brace, but I fabricated an X brace a la Conn and installed it further up the bell, so now it has two bell braces and the bell is extremely well triangulated.

Who knows, maybe some day when the work's all done and I have a workshop again I'll do something similar for my other old horns that just have that one wee wire for a bell brace.
 
For stuff like pearls I kind of like the epater-les-bourgeois touch of using "something" for a replacement. Just like my "Peter Piper Pizza and Games" token that serves as a LH thumb rest on my Mexi-Conn tenor, or the piece of cork that I used on my Conn baritone to raise the LH index finger touch to be even with the bis key. I look upon these repairs as signs of an instrument's long working life and evidence that making music was more important than keeping the thing a case queen.
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,059
Messages
578,328
Members
8,127
Latest member
PJ2116
Back
Top Bottom