Tech/maintenance (Re) Painting my sax?

About 20 years ago, I was in a store TV section, where they had various demonstrator models plugged in with various pre-recorded videos running to demonstrate their potential. These were the older flat screen TV's costing thousands of US dollars.

One had a tenor saxist playing a very nice solo jazz line on an outdoor stage. His sax was old, lacked much of its original lacquer finish with patina in places, and interestingly had visible dents, but he sounded really good. (Sound was plugged into a high end home theatrical sound system.)

Putting 2 and 2 together: I think where one may see a shiny new sax playing is if the camera zooms very close into the bell engraving to reveal the model / make, then pans out to view the saxist; it is not just a performance but doubles as a "prepaid advert" by that manufacturer or a major regional distributor of that sax.
About 50 or 60 years ago I remember seeing big bands on TV - Basie, Ellington, Benny Goodman, Lawrence Welk, even The Tonight Show. The light reflections off the horns would burn out the camera.

Looking “sharp” was emphasized by bandleaders. It was common for working saxophonists to have their horns relacquered every 4 or 5 years. Cultural norms change 🙂
 
Date is not given, but given the gray hairs on Johnny Carson and the Doc, perhaps the mid to late 1980's? (Show went off the air in 1992.) Here's Doc Severinsen's band in action with an older jazz tune with Doc soloing on trumpet and the tenor saxist has a solo. As you allude to, @skeller047 , all the horns including saxes are glistening, look new. The band is well dressed in coat and tie.

 
But in this day and age having a horn look nice and shiny is no longer a requirement. (I’m not saying this is a good thing, just that’s what it is.)
That may be true amongst players, but does it apply to our audience?

Feedback from my listeners is they like to see a shiny sax, and in the case of my alto, a full bling black lacquer with gold keys... The complement rate on my playing has rocketed since switching to the bling, which I put down to appearances
 
That may be true amongst players, but does it apply to our audience?

Feedback from my listeners is they like to see a shiny sax, and in the case of my alto, a full bling black lacquer with gold keys... The complement rate on my playing has rocketed since switching to the bling, which I put down to appearances
Yes, listening with their eyes.
 
I have to say I love to see a glistening gold sax they’re beautiful to me as a player and as a live music fan


Beauty is the eye of the beer holder. Personally, I appreciate a players horn. I recently watched a live band at a St Patty's Day gig where the tenor player was on a beat up silver SBA and I thought, "Respect."

My horns have miles on them (admittedly not all from me) and they have scars and blemishes. They're still beautiful. My wife has wrinkles and gray hair...
 
Beauty is the eye of the beer holder. Personally, I appreciate a players horn. I recently watched a live band at a St Patty's Day gig where the tenor player was on a beat up silver SBA and I thought, "Respect." My horns have miles on them (admittedly not all from me) and they have scars and blemishes. They're still beautiful.
It's likened to the motorcycling community, no one criticises another's ride regardless of what it looks like. 😉
My wife has wrinkles and gray hair...
I don't even go there, my balding head has gone through: :confused:

 
@MarkSax .....Hard for me to suggest products in UK, since I am trapped here for time-being....

I use Sculpt Nouveau - Patinas and Metal Finishes, they might ship abroad.

A lot of colorants, I find the most successful ones are the hot-applied (heat the brass with a torch, just a bit, then brush on).

They have two sealers...a wax sealer, and a spray-on polymer. They both work well...I mean the issue with hardware-store patina kits is it looks great as long as you don't touch it. Even cheapo sax mfr's offering 'antique' finishes, those finishes start coming off after some time.

The polymer gives the surface a matte 'feel' when you run your fingers across it. The wax finish is smoother. Pretty 'hard' finish the wax, dunno what is IN it but if you leave it on too long before buffing it you are in trouble because it sets after a certain amount of time and becomes less workable. I have actually heated areas with the wax finish and it didn't just melt off, it took the heat, surprisingly. Just needed to re-buff it lightly afterward,

One other option, leave it bare brass and seal it. For example I could see this company's wax sealer working quite well on a clean, bare brass horn.

There are some other waxes people DO use to slow down the patina/rot process on bare brass. One of my bandmates has a chinese jobber, factory bare, he just uses Pledge furniture polish 2x/year on the horn, assembled. It has darkened over the three years I have known him but has not developed "bad" patina...
 
There are some other waxes people DO use to slow down the patina/rot process on bare brass. One of my bandmates has a chinese jobber, factory bare, he just uses Pledge furniture polish 2x/year on the horn, assembled. It has darkened over the three years I have known him but has not developed "bad" patina...
Exactly. A sealer like that is sufficiently porous to oxygen to permit the patina to grow, but inhibits the easy transport of water and water-born chlorides (the stuff that leads to green or red corrosion products). Car polishes like Meguiars do a similar job.

The thermodynamic drivers remain but the competing reaction rates are controlled, thus the desirable patina can win out.
 
Having acid-selenium-ised brass... Is the resulting patina a defense against green and/or red blotches?

In other words... Is the acidified brass less, or even, not at all reactive to oxygen?

The patina remains permeable to ion exchange, so while it may slow the reaction, it won’t stop it. If it, for instance, gets sprayed with sea mist, it will still suffer attack from chloride corrosion. It you really want to stabilize the patina and suppress subsequent corrosive attack, the best bet is a clear overspray. Palo Tung at Just Saxes used to do exactly that - apply a patina and an overcoat.
 
Having acid-selenium-ised brass... Is the resulting patina a defense against green and/or red blotches?
It must be somewhat reactive as the good doctor says. It isn't fully sealed after all. But even lacquer doesn't fully seal the metal. I've only got 4 years on this one. That's just a blip in the lifetime of a horn. Hardly a long enough time to be sure of anything but, after 4 years, it hasn't changed.
 
But even lacquer doesn't fully seal the metal.
Depends upon the finisher, how well they cover all surfaces. There are always a certain amount of pinholes in painted finishes whether clear, tinted or colour. Fortunately where I currently live, in the high desert, we have usually low levels of humidity, which removes the electroyte through water moisture. This is why in just a few years, car bodies heavily rust out up north and east where there is more rain and snow and use of salt on roads during Winter.

Here until recently (now owned by another), I had a 24 year old pickup truck, a 1999 Chevrolet S10 that still didn't have a spot of rust on its body and its original non-metallic white paint would still polish up to look new. However when I move from here further northeast, I don't think I will have such luxury.

This is why I could let my early 1950's Beaugnier Vito low Bb Bari Sax go for a year, year and a half before I needed to apply a touch more of Brasso to clean up the patina from water moisture and handling, since it only has about 40% of its original lacquer left.

However if one lives in a place where even their notebook paper goes occasionally limp from the humidity may find it more necessary to wax more often and wipe acidic hand oils off more frequently IMO to keep the patina in check.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,058
Messages
578,320
Members
8,127
Latest member
PJ2116
Back
Top Bottom