Tech/maintenance Piece of swab stuck inside tenor neck

I wondered the same thing about an aerosol lubricant.
Back to the wire thing....a converted old school wire coat hanger would be about the right strength for a stiff cork screw but possibly not that flexible and a little thick to deal with. But I'm sure there is something out there. Just need that spot of inspiration in finding it.
 
I suspect that ramming a pencil down the crook pretty much sealed your fate. The pull-through was probably bunched up around the octave key pip tube, and all you've done is pack it down harder.
There's little point now it trying to push the wad out as a whole - you'll have to resort to picking it apart piece-by-piece until it loosens up enough to be withdrawn.

The tool I use for this is just a steel rod with a slot cut into it, filed to a taper and then splayed out at the end. Whichever way you turn it, it'll grip the cloth and allow you to gently tease the was out into a looser ball - after which time (and it'll likely be a very long time) the cloth should come out.

grabber.webp


Because of the position of the wad you have little choice but to go in from mouthpipe end - which means having to tease the cloth out into a narrowing tube. Not fun.

Wetting the cloth isn't likely to make much difference either way at this point but it just might help to soften the fibres. Try a very slightly diluted solution of dishwashing detergent. If it doesn't work, you'll just have to wait for it to dry out, and start over.

If all else fails I suspect you'll need to have the octave key pip removed. Hopefully it hasn't been damaged by hammering a pencil down the crook...

For future reference you're better off leaving the crook wet (just give it a shake at the end of playing) - and then washing it out on a regular basis with a flexible brush. Keeps the crook fresher and does a much better job of preventing the build-up of slime and calcium carbonate deposits.
The crook Pad-Savers are a decent alternative - but unlike the regular Pad-savers for the body of the horn I wouldn't advise leaving them in the crook.
 
Hello Erick I have had this happen to me.
My solution was to unlink a wire coat hanger bend the end of it over about two
inches and tape it. I then bent the hanger into roughly the same shape of the
neck, I then poured a small amount of washing up liquid into the cork end.
I allowed this to soak into the neck pull through. After about 20 mins I used the
wire and with gentle constant pressure the remains came out.
Good luck
Dale
 
I've done it too. More than once. Not just the neck. Can't remember how I got it out though.

The pictures only show black holes. So it doesn't give us a clue as to how to grab any part of the stuck bits.

Patience is key here.

Good luck !
 
I was thinking the octave pip has probably got snagged.

If you're going to carry on attempting this yourself - I'd remove the crook key to avoid bending it and putting it to one side - it should be just one screw.

I'm thinking you're probably going to have to pick it out in bits from both ends - try and avoid pushing as this will only compact things more.

In future, always use good quality swabs and mops/pad saver and make sure the you are using the correct one for the job. - I use these:

HW Pad saver

BG Neck Pull Though Swab
 
I found that clarinet hanky style pull throughs are also good to swab saxophone necks. I encouraged my students to have someone sew a length of cotton shoelace on the end opposite to the weighted string so it can be pulled out if/when it gets stuck. In my shop I invested in different sizes and shapes of forceps to pull stuck things out of neck and body tubes.

1692458443058.webp
 
Hello everyone. I'm really thankful and highly appreciative of all this wonderful feedback for my problem. I like taking good care of my saxophones, so this situation was a bit upsetting. Especially when I pounded a pencil into the neck with a hammer. Hopefully some of these tips and suggestions will do the trick. I'll keep you all updated. Tomorrow I have to drive 6 hours to pick up my family returning from abroad, staying overnight at a hotel etc. So I don't think I'll have time to try out any of this until Thursday or Wednesday. Looking forward to it though. Can't wait to tell you all what worked for me
 
Sounds as if it’s pretty impacted. I might try introducing a scalpel blade on a long handle (if it will fit) and seeing if I could make a series of cuts to create some loose bits that can gradually be pulled out and eventually loosen the rest.
 
I found that clarinet hanky style pull throughs are also good to swab saxophone necks. I encouraged my students to have someone sew a length of cotton shoelace on the end opposite to the weighted string so it can be pulled out if/when it gets stuck. In my shop I invested in different sizes and shapes of forceps to pull stuck things out of neck and body tubes.
'have someone sew a length of cotton shoelace on the end'?
There are long threads on here about how to maintain, repair, rebuild saxophones and yet if you want a skilled job doing such as a bit of sewing it is best to ask your mother.
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,072
Messages
578,569
Members
8,133
Latest member
walthang
Back
Top Bottom