Tech/maintenance Mouthpiece Bore Sizes & Suitable Hand Reamers

With the drill bit held in a vice I got enough purchase to twist the mouthpiece off.

I have since been trying to use that setup to remove more material but although quite a lot has been removed the drill only wants to go about one inch into the bore. I have been backing it out and cleaning off the ebonite pieces but think this is not the way to go so may leave it alone now.

Thanks for the help.

Rhys (a rookie)
You could always rounding off the tip of the drill a little (just take a little of the edge off with a sharpening stone). Might allow the drill to progress into the bore a little easier. Don't think you have much to lose at this point.
What you really need for the job is a reamer...and drills tend to make crappy reamers.
 
A drill with cutting edge angles designed for steel may tear lumps out of ebonite.

A reamer is designed differently but still may need a high speed to be accurate.
I'd leave it to someone used to working with ebonite unless it's a piece you're willing to experiment on and don't mind losing.

It's probably easier and safer to recork for different mouthpieces.
 
One thing you could try, if you have a drill with reverse rotation (like everyone out there) run it in reverse. Use canola oil or something similar to lubricate the bore and prevent it from burning. I don't know if it will work but that's about the only thing I could suggest right now.

If you were here, I'd be happy to do it for you in 5 min.
 
Tangential to topic but how come there isn't a more modern solution to cork? Some clarinet mouthpieces come with what looks like double o-rings:

Screenshot_20220405-090610_DuckDuckGo.webp
 
Tangential to topic but how come there isn't a more modern solution to cork? Some clarinet mouthpieces come with what looks like double o-rings:

View attachment 20027
There was a guy Jim Scimonetti in the US patented this method and who used to fit o rings onto your crook.
GUO flutes ( who also make sax necks) do one: I prefer the belt and braces version
 

Attachments

  • Screenshot 2022-04-05 at 10.10.29.webp
    Screenshot 2022-04-05 at 10.10.29.webp
    5.4 KB · : 314
  • Screenshot 2022-04-05 at 10.13.22.webp
    Screenshot 2022-04-05 at 10.13.22.webp
    19.1 KB · : 157
Eventually I paid £10 for a Heller 17.5mm HSS drill bit for use on baritone mouthpieces.

Lending out tools is usually a big no-no....but....wanna borrow this?
17.5mm (nominal) D-bit reamer. If it works for you (and it bloomin' well should) you can drop a donation into the Cafesax coffers.
Can post it up to you.

17_5 d bit.webp
 
There's also the Warburton modular necks if you have money to burn:

 
Last edited:
Lending out tools is usually a big no-no....but....wanna borrow this?
17.5mm (nominal) D-bit reamer. If it works for you (and it bloomin' well should) you can drop a donation into the Cafesax coffers.
Can post it up to you.

View attachment 20030

That's a kind offer - or I could pop down to the workshop and D-Ream there and then. You wouldn't have to let it out of your sight and there might even be a pint on offer.

Wasn't that nice Brian Cox in D-Ream ?

Rhys
 
Last edited:
Sounds like a plan!
It took a while but the plan came to fruition earlier this week when I had a nice visit to Steve's workshop for him to tweak my new Bauhaus sopranino and also to properly ream my Dolnet baritone mouthpiece.

It was good for me to see how @Stephen Howard went about using the reamer - holding it in the chuck of his lathe but rotating it by hand and gradually removing material (and cleaning up the mess I had left by using a twist drill).


Rhys Dolnet Bari Mouthpiece on D Reamer in lathe chuck 1.JPG


Rhys Dolnet Bari Mouthpiece on D Reamer in lathe chuck 2.JPG


It was surprising to see how much material was removed in the end and interesting to see how Steve sharpened the cutting edge, cooled down the tool and lubricated it at various points.

The cut went about 50mm (2") into the bore and the mouthpiece is now a perfect fit on the neck cork. It is a "classical" style mouthpiece so has a small tip opening and I will need to go up in reed strength. The sound is very nice, but certainly not edgy or bright.

Rhys
 
Last edited:
It took a while but the plan came to fruition earlier this week when I had a nice visit to Steve's workshop for him to tweak my new Bauhaus sopranino and also to properly ream my Dolnet baritone mouthpiece.

It was good for me to see how @Stephen Howard went about using the reamer - holding it in the chuck of his lathe but rotating it by hand and gradually removing material (and cleaning up the mess I had left by using a twist drill).


View attachment 20488

View attachment 20490

It was surprising to see how much material was removed in the end and interesting to see how Steve sharpened the cutting edge, cooled down the tool and lubricated it at various points.

The cut went about 50mm (2") into the bore and the mouthpiece is now a perfect fit on the bore. It is a "classical" style mouthpiece so has a small tip opening and I will need to go up in reed strength. The sound is very nice, but certainly not edgy or bright.

Rhys
More power to @Stephen Howard :happydance:
 
Hi Rhys,
I missed all of this thread due to my infrequent forum visits but....
I needed to open the shank bore on one of the 'new slant' ebonite Otto links a couple of years back.
So if you are talking ebonite... I am a rookie but it worked out well because there wasn't much that could go wrong.
My method was to cut glass paper, sand paper, emery. cloth (what ever I had handy) into a width that was as wide as the shank is long. I didn't find I needed to be too fastidious about that though. Then I wrapped the paper around the diameter of wooden dowel that had I cut a slit in the top of to accept the leading edge of the paper.
Along with different grit papers and how much I wrapped around the dowel it made the incremental adjustment very easy yet owing to the whole shank length being adjusted (as opposed to winding a drill in from the end) the dowel and paper made a stable combination to increase the bore size uniformly.

Would it be possible to cut strips of grit paper for where the drill got to and the internal end of the shank bore and try this method with a dowel fairly close to the shank bore diameter? That might bring the 2 diameters you have ended up with together.
That said the smaller the diameter of the dowel the more forgiving the relationship between the gritted surface and the ebonite.
Also this meant I didn't have to calculate 0.5mm and get mixed up with radius and diameter which I would have been perfectly capable of doing and giving myself the opposite problem. Instead I just kept trying the new bore size on the neck cork until I was satisfied.
P.S>
Gritted paper is easily man enough to make light work of it. It won't be like cutting grass with scissors.
 
Last edited:
Would it be possible to cut strips of grit paper for where the drill got to and the internal end of the shank bore and try this method with a dowel fairly close to the shank bore diameter? That might bring the 2 diameters you have ended up with together.
That said the smaller the diameter of the dowel the more forgiving the relationship between the gritted surface and the ebonite.
Also this meant I didn't have to calculate 0.5mm and get mixed up with radius and diameter which I would have been perfectly capable of doing and giving myself the opposite problem. Instead I just kept trying the new bore size on the neck cork until I was satisfied.
P.S>
Gritted paper is easily man enough to make light work of it. It won't be like cutting grass with scissors.

Now @Stephen Howard has done his reaming it is a lovely smooth bore that finishes cleanly. It isn't easy to photograph up inside the mouthpiece and get it properly lit and in focus.

There was a lot of ebonite material removed in total between my botched job with the drill bit and Steve's "proper job" with the reamer.

Your method sounds like a good one for a one-off DIY job on ebonite so I might well try that if I have another piece with a small bore that needs to be expanded.

Rhys
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,077
Messages
578,684
Members
8,136
Latest member
peterdehelegrote
Back
Top Bottom