The abrasive in it is too coarse. The finish it leaves is not high polish.How exactly is Brasso bad for a brass horn? It's great for filthy brass candlesticks
The abrasive in it is too coarse. The finish it leaves is not high polish.How exactly is Brasso bad for a brass horn? It's great for filthy brass candlesticks
We used Brasso in the Army going back to the early 1970's. It is an older product.The abrasive in it is too coarse. The finish it leaves is not high polish.
Applying key oil to hinge key points is not sufficient. If it’s been a while, remove the rod, clean the tube, and then lube and reassemble.If it's been a while, I may gently apply key oil to key hinge points, use a Q-Tip / rag / felt pipe cleaner to wick up any excess.
Apologies to all for not including a link. Here ya go:Applying key oil to hinge key points is not sufficient. If it’s been a while, remove the rod, clean the tube, and then lube and reassemble.
See Matt Stohrer’s YouTube video on “Changing the Oil”.
There is a heavy chemical in it, quite ammoniac-smelling, and the grain of it is too large or less fine than, say, Wenol or Mass or Flitz. So, while it attacks rot pretty well, the resulting area does actually end up with 'more metal removed from it' than, the others.This has been written before, perhaps by you
'Stringent' doesn't really say what the actual issue is
How exactly is Brasso bad for a brass horn? It's great for filthy brass candlesticks
I really liked Simichrome for nickelplate.....it's better on nickelplate than the others I like, almost as if it were more made for it.Why do you prefer Maas or Wenol over Simichrome?
(Just as an aside, I can't find Maas or Wenol in hardware stores here, but Simichrome is SOMEWHAT available.
Maybe, maybe not. For areas showing verdgris or red rot in difficult to get locations, q-tips and threading and pulling cloths thru the keywork areas isn't gonna really do it.If meticulous, one can reasonably clean their sax without any disassembly or loosening key rods. Use a variety of cleaning tools such as cloths, paper towels, Q-Tips, felt pipe cleaners, a gentle cleaning agent, toothpicks and etc.
Actually my point in cleaning was more in general, and in the cases you mention, some areas could be untouchable without a disassembly. Even a new sax gets dusty and dirty. I've found that to do a little non-disassembly detailing cleans things up quite nicely. It doesn't have to be 100% perfect to look acceptable. Removal of the dust and split splashes does wonders for appearances. Careful oiling of the keys with a quality oil continues smooth operation.Maybe, maybe not. For areas showing verdgris or red rot in difficult to get locations, q-tips and threading and pulling cloths thru the keywork areas isn't gonna really do it. Typical example - rot or verdgris at the base of posts. Those need significantly aggressivve treatment..a q-tip slathered with polish isn't gonna do the job.
The reason these nasties happen is lack of upkeep to begin with, so I applaud you on your efforts.Actually my point in cleaning was more in general, and in the cases you mention, some areas could be untouchable without a disassembly. Even a new sax gets dusty and dirty. I've found that to do a little non-disassembly detailing cleans things up quite nicely. It doesn't have to be 100% perfect to look acceptable. Removal of the dust and split splashes does wonders for appearances. Careful oiling of the keys with a quality oil continues smooth operation.
Plus, I am not afraid to do partial disassemblies if required. I am meticulous enough to get it back together without harm to adjustments. Remember the clocks and clock radios with flippy digital numbers common back in the 1970's? Mine developed problems, I had it all apart with gears, springs, rods, etc. all over the place. My roommate wondered if I'd ever get it back together again. But I did, fixed the problem and had it all back together again without left over parts. Worked fine for another couple years.
Keep playing it. That’ll blow off !Taking my beater Silversonic out after a while, I noticed it's developed a rather red-rusty line across the B/Bb key guard:
View attachment 31527
I don't know... in a certain light...
View attachment 31528
I kinda dig it.
Brasso and Dezincification RiskThis has been written before, perhaps by you
'Stringent' doesn't really say what the actual issue is
How exactly is Brasso bad for a brass horn? It's great for filthy brass candlesticks
I don't, it's a 5-minute removal job with any of the polishes aforementioned in this thread...Taking my beater Silversonic out after a while, I noticed it's developed a rather red-rusty line across the B/Bb key guard:
View attachment 31527
I don't know... in a certain light...
I kinda dig it.
That explains it, yeah for the job it needs to do on musical instruments, you don't need the ammonium in there...Brasso and Dezincification Risk
Brasso contains ammonium hydroxide. Ammonia is a substance that can cause stress corrosion cracking and may contribute to dezincification in susceptible brasses, particularly the common CuZn30 alloy used in many applications, including musical instruments.….this from a quick AI search.
Dezincification is a common concern in treatment of brass objects in museums, visually it can result in pink coloration as the alloy surface moves to a higher relative copper content.
