Tech/maintenance I did it! πŸ˜‚πŸ˜‰πŸŽ·

Well done,question, I need to replace neck cork soprano sax,anyone know of supplier to get correct thickness of cork.
Any seller of saxophone supplies, including Amazon has "neck corks". The main difference is the quality of the material, the cheap ones often have an excess of "woody" grain, which makes them brittle.
And you can run into the same issue even with more expensive suppliers. But if you buy a 10-pack, there will usually be at least 2 or 3 decent ones.

The key is the softening using a hammer or preferably a ball peen, and then the taper that you have to sand on the end that goes on the neck first so that you can create a good overlap/transition. There are lots of YouTube videos on how to do it.
 
Well done,question, I need to replace neck cork soprano sax,anyone know of supplier to get correct thickness of cork.
Having a split cork and nothing to hand and a looming gig, I used some self adhesive composite cork for under ornaments as a temporary fix.

Still going strong months later. No overlap just a butt joint. Spare piece in the case, just in case. πŸ˜‰
 
Having a split cork and nothing to hand and a looming gig, I used some self adhesive composite cork for under ornaments as a temporary fix.

Still going strong months later. No overlap just a butt joint. Spare piece in the case, just in case. πŸ˜‰
And @BUMNOTE Stephen @Stephen Howard recommends wrapping PTFE tape Plumbers tape) around the neck cork as a temporary measure until repairs can be made too 😊
 
Any seller of saxophone supplies, including Amazon has "neck corks". The main difference is the quality of the material, the cheap ones often have an excess of "woody" grain, which makes them brittle.
And you can run into the same issue even with more expensive suppliers. But if you buy a 10-pack, there will usually be at least 2 or 3 decent ones.

The key is the softening using a hammer or preferably a ball peen, and then the taper that you have to sand on the end that goes on the neck first so that you can create a good overlap/transition. There are lots of YouTube videos on how to do it.
They're usually fine - I use them all the time.
You really don't need the best quality cork for a mouthpiece cork because you'll be loading the rear of it up with adhesive (which holds any loose particles in) - and then loading the surface of it up with your preferred cork grease (which fills any holes).
A sheet of premium grade cork at 1.6mm is Β£16. You'll need that quality for keywork - but for 'neck corks' the cheapo stuff is more than up to the job for half the price.

The advice to soften the cork with a hammer is good - but it applies even more so to the expensive stuff when it comes to crook corks.
Been there. Done that.
 
They're usually fine - I use them all the time.
You really don't need the best quality cork for a mouthpiece cork because you'll be loading the rear of it up with adhesive (which holds any loose particles in) - and then loading the surface of it up with your preferred cork grease (which fills any holes).
A sheet of premium grade cork at 1.6mm is Β£16. You'll need that quality for keywork - but for 'neck corks' the cheapo stuff is more than up to the job for half the price.

The advice to soften the cork with a hammer is good - but it applies even more so to the expensive stuff when it comes to crook corks.
Been there. Done that.
I used my marble rolling pin cos I thought my 2.5lb lump hammer would be overkill πŸ˜³βš’οΈ and also my table probably wouldn't have survived either πŸ€”πŸ™„πŸ˜‚
Actually, thinking about it,.... Should I have bashed it with the rolling pin instead of rolling it like a piece of pastry?.... πŸ€”
 
I used my marble rolling pin cos I thought my 2.5lb lump hammer would be overkill πŸ˜³βš’οΈ and also my table probably wouldn't have survived either πŸ€”πŸ™„πŸ˜‚
Actually, thinking about it,.... Should I have bashed it with the rolling pin instead of rolling it like a piece of pastry?.... πŸ€”
Did it crack on you when you wrapped it round? No.
Did it do the job? Yes.
Don't worry about it.
 
I used my marble rolling pin cos I thought my 2.5lb lump hammer would be overkill πŸ˜³βš’οΈ and also my table probably wouldn't have survived either πŸ€”πŸ™„πŸ˜‚
Actually, thinking about it,.... Should I have bashed it with the rolling pin instead of rolling it like a piece of pastry?.... πŸ€”
My kinda lass... bash the cork into submission >:):happydance::banana:
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,063
Messages
578,433
Members
8,130
Latest member
tommyliehe
Back
Top Bottom