teen37
Member
- Messages
- 275
- Location
- Dudley, West Mids
What!..... π³ Where... How....? π³π³π πππNo itβs that obvious.
What!..... π³ Where... How....? π³π³π πππNo itβs that obvious.
π Thank you so much I'm super pleased I didn't cock it up ππAin't no need for a microscope. But it's a battle scar, wear it with pride!
Good job!
If thereβs a scratch blame the cat.What!..... π³ Where... How....? π³π³π πππ
Nah...I think it's because I've seen so many scratched-up crooks that it's the first place I look. πAnyway, you must've looked through those pics with a microscope to see that π³ π
Any seller of saxophone supplies, including Amazon has "neck corks". The main difference is the quality of the material, the cheap ones often have an excess of "woody" grain, which makes them brittle.Well done,question, I need to replace neck cork soprano sax,anyone know of supplier to get correct thickness of cork.
I got a pack of 10 off amazon for Β£8.49 it said they were for sax, clarinet, soprano, you have to lightly sand to correct thickness once fitted ππWell done,question, I need to replace neck cork soprano sax,anyone know of supplier to get correct thickness of cork.
Having a split cork and nothing to hand and a looming gig, I used some self adhesive composite cork for under ornaments as a temporary fix.Well done,question, I need to replace neck cork soprano sax,anyone know of supplier to get correct thickness of cork.
Do you mean me? π€ If so, I have a leak light and I've used it already πWell done. Now buy a leak light. π
And @BUMNOTE Stephen @Stephen Howard recommends wrapping PTFE tape Plumbers tape) around the neck cork as a temporary measure until repairs can be made too πHaving a split cork and nothing to hand and a looming gig, I used some self adhesive composite cork for under ornaments as a temporary fix.
Still going strong months later. No overlap just a butt joint. Spare piece in the case, just in case. π
They're usually fine - I use them all the time.Any seller of saxophone supplies, including Amazon has "neck corks". The main difference is the quality of the material, the cheap ones often have an excess of "woody" grain, which makes them brittle.
And you can run into the same issue even with more expensive suppliers. But if you buy a 10-pack, there will usually be at least 2 or 3 decent ones.
The key is the softening using a hammer or preferably a ball peen, and then the taper that you have to sand on the end that goes on the neck first so that you can create a good overlap/transition. There are lots of YouTube videos on how to do it.
I used my marble rolling pin cos I thought my 2.5lb lump hammer would be overkill π³βοΈ and also my table probably wouldn't have survived either π€ππThey're usually fine - I use them all the time.
You really don't need the best quality cork for a mouthpiece cork because you'll be loading the rear of it up with adhesive (which holds any loose particles in) - and then loading the surface of it up with your preferred cork grease (which fills any holes).
A sheet of premium grade cork at 1.6mm is Β£16. You'll need that quality for keywork - but for 'neck corks' the cheapo stuff is more than up to the job for half the price.
The advice to soften the cork with a hammer is good - but it applies even more so to the expensive stuff when it comes to crook corks.
Been there. Done that.
Did it crack on you when you wrapped it round? No.I used my marble rolling pin cos I thought my 2.5lb lump hammer would be overkill π³βοΈ and also my table probably wouldn't have survived either π€ππ
Actually, thinking about it,.... Should I have bashed it with the rolling pin instead of rolling it like a piece of pastry?.... π€
How do you Brits state that? The proof is in the puddink!Did it crack on you when you wrapped it round? No.
Did it do the job? Yes.
Don't worry about it.
Almost! π "the proof is in the pudding" ππHow do you Brits state that? The proof is in the puddink!
My kinda lass... bash the cork into submissionI used my marble rolling pin cos I thought my 2.5lb lump hammer would be overkill π³βοΈ and also my table probably wouldn't have survived either π€ππ
Actually, thinking about it,.... Should I have bashed it with the rolling pin instead of rolling it like a piece of pastry?.... π€



