Tech/maintenance Final pad print

motondo

Member
Messages
29
Location
Spain
Hello everyone.
I just repaded a YTS 23. This is my first pad-work and so far the result seems pretty good.
I would like to ask you what is the right time to print the pads and how it should be done. I have found information about the saxophone repad but no details about the final printing. Thank you
 
I’m not sure what your definition/expression “print” is. Are you asking about the impression indentation made into the leather pad? If so it is not entirely necessary. If the pad is sealing all the way around leave it be. Pads do not always need an impression to make them seal well.
 
Welcome to the "yts23 first re-pad club"!

I'm also an amateur - but, seems to me, if a pad doesn't seal under pressure it needs adjusting... Then the dent will form, eventually, by itself...
.... But the last few% can be fiddley / frustrating.
 
Absolutely ! With a little observation, the leak lamp and iron pad as main tools. I was able to determine the fit of the pads. The first attempts were a little stressful for me, but as I have done the successive keys I have felt the satisfaction of controlling the process. Thank you so much
 
Absolutely ! With a little observation, the leak lamp and iron pad as main tools. I was able to determine the fit of the pads. The first attempts were a little stressful for me, but as I have done the successive keys I have felt the satisfaction of controlling the process. Thank you so much
I watch to see if a ring partially forms on the pad. If so then one side probably a bit too high. I try to get the pad sealing with as little pressure as possible. Don't forget that some keys also actuate others so you may be fighting with these needing adjustment to get the one that you are working on to seal.
 
Hello, I'm sorry I didn't respond sooner.

It is very important that the key sits well on the tone hole without applying pressure. I have tried to make it so.
So far I am very happy with the result. Thank you so much.
 
I’m not sure what your definition/expression “print” is. Are you asking about the impression indentation made into the leather pad? If so it is not entirely necessary. If the pad is sealing all the way around leave it be. Pads do not always need an impression to make them seal well.
Yes, indeed the sprung open pads won't form an impression when fitted. Some manufacturers force them closed with wedges so as to for an impression and seal but I think this may be an excuse for poor levelling of pads i.e. the cheaper brands seem to do this more often.
 
After the pads are installed and seal and key keys works fine you maybe have to check so the pad seal (light pressure) against the tone hole. If you need to do some minor correction you use a pad ironer that you heat up. The heat from the pad ironer makes the pad to flatten out. Now is not light pressure, press down the key with a rather rather firm pressure. Remove the pad iron and press the key/pad against the tone hole. Heat the outside of the key cup while you are pressing. I used rubber wedges that I placed under the key foot to hold the key against the tone hole. This is called "burning in" or "seating".

I just used shellack and never reached the level to use glue.
 
Last edited:
After the pads are installed and seal and key keys works fine you maybe have to check so the pad seal (light pressure) against the tone hole. If you need to do some minor correction you use a pad ironer that you heat up. The heat from the pad ironer makes the pad to flatten out. Now is not light pressure, press down the key with a rather rather firm pressure. Remove the pad iron and press the key/pad against the tone hole. Heat the outside of the key cup while you are pressing. I used rubber wedges that I placed under the key foot to hold the key against the tone hole. This is called "burning in" or "seating".
I've often found this method to be unreliable over time - and generally now only use it when I'm doing a "quick and dirty setup" to see if a horn's worth spending money on. About the only time I'll use a heated pad iron is when the leather is a bit ruched up (typically when fitting oversized pads).
The felt core of a pad always seems to want to find its own natural equilibrium - so the most effective way to ensure a stable seat is to work the pad from its base, apply the absolute least amount of pressure to the face of the pad and give it time to relax afterwards before checking it again.
 
I've often found this method to be unreliable over time - and generally now only use it when I'm doing a "quick and dirty setup" to see if a horn's worth spending money on. About the only time I'll use a heated pad iron is when the leather is a bit ruched up (typically when fitting oversized pads).
The felt core of a pad always seems to want to find its own natural equilibrium - so the most effective way to ensure a stable seat is to work the pad from its base, apply the absolute least amount of pressure to the face of the pad and give it time to relax afterwards before checking it again.
I just followed the tips and techniques that I could read about in "Band Instrument Repairing Manual" by Erick D. Brand (copyright 1939, 1942, 1945, 1946). And I just worked on my own saxes. I sold some student saxes and I gave the buyers lifelong gaurantee on the on the work. Still some guys that call me for some adjustments. Lifelong friendship as well? If my saxophone repair/service was going to pay my bills ... no family, house, car .... I had to live on my own in a small cottage in the woods.
 
I just followed the tips and techniques that I could read about in "Band Instrument Repairing Manual" by Erick D. Brand (copyright 1939, 1942, 1945, 1946). And I just worked on my own saxes. I sold some student saxes and I gave the buyers lifelong gaurantee on the on the work. Still some guys that call me for some adjustments. Lifelong friendship as well? If my saxophone repair/service was going to pay my bills ... no family, house, car .... I had to live on my own in a small cottage in the woods.
Yeah, I get that - and I used to 'iron' the pads. But I found a better way. Give it a try...won't cost you anything but your time.
 
I wonder if @Woodpad has a pad in the woods where he makes his pads made from wood, perhaps from wood from the wood where his pad is?
I use polyester pads with a silicone membrane and have possibility to grind my pads to the correct height. It is a system with other advantages/disadvantages than more traditional materials and still a work in progress.
 
So Woodpad's pad is a polyester pad in the presidio on Pecan hill pres de la Polytechnique?

(it's an English word play on 'pad,' which can be an informal, 'hip' way to say 'house')

t
whose gramma was Dutch, and did not get the finer nuances of the 60's generation. At all.
 
So Woodpad's pad is a polyester pad in the presidio on Pecan hill pres de la Polytechnique?

(it's an English word play on 'pad,' which can be an informal, 'hip' way to say 'house')

t
whose gramma was Dutch, and did not get the finer nuances of the 60's generation. At all.
Correct, English is my turd language.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,070
Messages
578,523
Members
8,132
Latest member
LouisJR
Back
Top Bottom