Tech/maintenance Do you carry out your own repad?

Do you replace your own pads?


  • Total voters
    48
I rather doubt those little animals have thick enough skin to make useful leather.
^^^^
Might work for pads, but it's a NoNo in the Little Critter Recipe Book.
It would make for small talk with the guitar or violin player: "My pads are made of cat gut, too." 😉
I was just wondering if he had some number memorized 😎
I gather they are used to do high volume work. Unless something is unusual, most is labour costs with a small amount for parts and supplies with "clean, oil and adjust". The items above and beyond would be extra cost items. Detailed paperwork takes more time. Their "minor costs plus COA" is probably a calculated historical average, cuts down on admin paperwork time.

A one technician shop may benefit more by being further detailed.
My material costs per pad is less than 1% of that.
Figuring that I spent maybe $30 US in a pad kit with a few pads extra, say at $50 in parts with my own labour, add tech costs of $151.12 for a total of say, $200.00 for a complete overhaul job, I would say my doing was worth it.

Would I do it again? Being older now, I'd just put up extra quid and have someone else be done with it.
 
I bought a reduced keywork Eb clarinet to travel with.

It had two obvious torn pads (and another I discovered while working on it)

As it is worth so little financially and there aren’t huge numbers of keys to take off / put back I thought I’d have a go.

I had some old glue and key oil. I found a cheap Eb clarinet pad set online. Left them all to fester for a while and I procrastinated. Then got around to it finally.

I was pretty ham fisted and used too much glue in one cup (it oozed) but the instrument does work better now.

I wish I had done before and after photos for posterity.

I wouldn’t do it on a good instrument but might if I needed to do a gig and didn’t have another option.
 
I wouldn’t do it on a good instrument but might if I needed to do a gig and didn’t have another option.
During late Fall outdoor play, I had a pad pop loose on my Selmer Bundy II alto sax, one of the smaller pads around high C. I had a roll of black electrical tape in my car. Looped it, put the pad back into place, allowed me to finish the night.

Some time back, used to buy a sax emergency repair kit (also bought a separate clarinet kit) that came in a small box about the size of a 10-box of sop reeds. It was white with blue letters and graphics, forgot who made it. Came with a couple common size pads, a tube of shellac glue, some replacement needle and flat springs, mouthpiece cork, few pieces of sheet cork in various widths, and I think a small section of sandpaper.

A number of times over the years I have purchased and used those kits. Was a life saver. Also a small pack of jewelers screwdrivers was helpful.
 
I wouldn’t do it on a good instrument but might if I needed to do a gig and didn’t have another option.
For the likes of me, that's the bottom line. Know enough to navigate around and keep things ticking over; but leave the heavy lifting to a pro...
... But also, know what you want from a pro tec.
I don't have such good support from the local tec early on. In retrospect.
 
I'd rather spend my time practicing my horn than working on it. I'll leave that work to my tech, who does a stellar job.

I wish I had a stellar tech to rely on. Lack of one is what drove me to tackle my first overhaul. Our local shop is really only interested in school work. I don't trust them with anything more than basic dent work. If I have to explain to the tech what I mean by "neck tenon" then they're not touching my horn (yes, actually happened).

The alternative of shipping half way across the country to a qualified tech isn't appealing either. That Buescher tenor I mentioned in post #55 arrived to the tech after being dropped or thrown hard enough for the neck receiver to break through the side of the wood case, bending the body tube.
 
I wish I had a stellar tech to rely on.
I was the same as you. Living in rural towns for the past 30+ years, the absence of good techs and attempting to find good techs was difficult, so I fixed my horns. Recently I found that Tarpleys, Lubbock, Texas has a decent tech. So, I sent my Bundy II alto and Vito YTS-23 stencil to them. The alto plays like a new instrument. Now just need to wring out the Vito.
 
I wish I had a stellar tech to rely on. Lack of one is what drove me to tackle my first overhaul. Our local shop is really only interested in school work. I don't trust them with anything more than basic dent work. If I have to explain to the tech what I mean by "neck tenon" then they're not touching my horn (yes, actually happened).

The alternative of shipping half way across the country to a qualified tech isn't appealing either. That Buescher tenor I mentioned in post #55 arrived to the tech after being dropped or thrown hard enough for the neck receiver to break through the side of the wood case, bending the body tube.
I bought my first instrument from a very good tech and live in the area with the most techs. Still when studying I became self sufficient as I found the tinkering soothing. I have seen a few techs that can rival the first and seen a lot of bad repairs from others. The best techs attract so much work that they have a terrible waiting list. I can repair most things in a few hours so only in a few cases I will ask a tech do some work on my saxophones. They are always suprised when they see my home made pads.
 
Generally speaking, I have a tendency of wanting to get to know the technical aspects of whatever I do.
I like to work on my own bicycles, do some basic carpentry, sowing my own plants (even harvesting some seeds), .....

But I never got around to tinkering with my saxophone. Possibly because I started playing the saxophone when I was almost 40. And generally, as I get older, I see myself using more and more professionals to do the work I used to do myself. Fixing bicycles has gotten more technical, so I leave that to a few very good technicians.

I did get Stephen Howard's book, that means that I still have some yearning to understand the technical aspects, and maybe one day (when I have more time) I might get around to it......
 
30+ years ago I worked with Rupert Noble in Nottingham. I’d strip the saxes down, clean them up, repad them and then hand them to Rupert to finish them off. Since then I’ve not had to do a great deal to my own instruments except occasionally take them down to Worthing (where Rupert now resides) for a bit of a tinker. I’m sure I could replace pads, but I’ve not had to.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,060
Messages
578,367
Members
8,128
Latest member
Roger Atlas
Back
Top Bottom