Playing the saxophone A Very, Very Basic Guide To Going Wireless On Stage

Veggie Dave

Sax Worker
Messages
3,466
Location
Citizen of Nowhere
As there's been a fair bit of talk about using wireless mics/systems recently, I thought some of you might find it useful to read my experiences over the last two years of teching a 9-piece band that's predominantly wireless.

This is a very, very basic guide to using wireless systems on stage, that's aimed at smaller shows/bands who are most likely using all sorts of kit that's owned by the individual musicians, rather than a big production with an integrated system.

To cut a long story short (😉) ; transmitters, receivers, Wi-Fi routers and Induction Hearing Loops don't mix.

If you're running wireless mics and wireless IEMs then you need to keep the two systems physically separate. You can get away with a gap of just 60cm between a mic receiver and an IEM transmitter. However, if at all possible, 1m or more is preferable - especially as the number of receivers and transmitters increases.

Line of sight also reduces potential interference issues massively. By this I mean there should be as few obstacles between the receiver and transmitter as possible. For example, if your sax mic uses a 'belt' transmitter, you put that transmitter on your body so that it can physically see the receiver. Your body is incredibly good at absorbing both analogue and digital signals. So are other musicians on that stage.

If you have your mic transmitter on the horn itself, then removing as many physical obstacles between it and the receiver is even more important. Reducing the distance between the two can really lower potential issues.

Wi-Fi routers need to be kept away from any other wireless equipment no matter whether those systems are analogue or digital. If you're using IEM that allows each band member to control their own mix then that router should also be positioned so that there are as few physical obstacles between it and the musicians as possible. Venues, theatres etc. all have internal Wi-Fi systems (often multiple systems) these days, that are more than capable of interfering with your Wi-Fi signal.

Also check to see if the venue you're playing is using an Induction Hearing Loop. If they are, get them to turn it off if possible - and assuming your show doesn't need it. Induction loops can cause uncontrollable feedback, even on a completely silent stage.

Dialling in the system:
This really should be done either during a normal rehearsal or during a tech rehearsal. If at all possible, don't leave this part until you're at the venue, just in case. You never know what's going to happen during soundcheck at the best of times, so don't take the chance.

Start with everything other than the Wi-Fi router (if you're using one) turned off. Decide whose wireless system is the most important (your criteria for this will be subjective to your specific band/show) and turn it on. Make sure it's working perfectly. If there's an issue, change its channel until it works faultlessly. If this doesn't help, move the system further away from the router and start again. Once you're happy, move on to the next system and repeat. You should be able to get the whole band up and running really (or, at least, pretty) quickly. Once your set-up is solid, it should work perfectly every time from that point on. This tech rehearsal also means you can work out where everything is going to physically go, too. Keep everything as neat and repeatable as possible and you're good to go.

If you're using a system where the receiver plugs directly into the mixer/stage box (it looks like a large XLR connector, such as the Nu-X system), plug the receiver into an XLR cable first and plug that into the mixer. You can't assume there's enough space to plug the receiver into the mixer/stage box. This type of system is also very popular with guitarists, so your receiver may not be the only one, which potentially leaves even less space. Depending where the mixer/stage box is, there could also be numerous physical obstacles between you and it. Use an XLR cable (or have one ready to go, just in case) and you instantly remove all these issues. No problem with plugging it in, no problems with line of sight as you can put the receiver anywhere you want.

I know this is a lot of text, but it's a lot of words to describe something that shouldn't take any time at all to actually do when you're setting up on stage (or in the rehearsal room).
 
Last edited:
Not having ever set-up a stage for wireless...

None the less, two thoughts.
the nu-x says it's using 2.4 GHz IMS - same as most popular WiFi devices.
1/ these days most WiFi routers, phones etc. Can use the 5Ghz band. If you could get everyone on stage onto 5Ghz and switch off the 2.5 radio on the router, you'd probably be doing yourself a favour.

2/ If I was setting up a stage I'd consider putting the WiFi router quite high up so that at least it's transmitter was further away. As well as it having better line of site (even more so for 5Ghz) to on-stage gadgets.
 
Last edited:
Not having ever set-up a stage for wireless...

None the less, two thoughts.
the nu-x says it's using 2.4 GHz IMS - same as most popular WiFi devices.
1/ these days most WiFi routers, phones etc. Can use the 5Ghz band. If you could get everyone on stage onto 5Ghz and switch off the 2.5 radio on the router, you'd probably be doing yourself a favour.

2/ If I was setting up a stage I'd consider putting the WiFi router quite high up so that at least it's transmitter was further away. As well as it having better line of site (even more so for 5Ghz) to on-stage gadgets.
It will never happen. If you did this, all the legacy devices in the venue would be disabled. Which will most likely include the credit card readers, ordering systems for the waiters/waitresses etc.

But it's not a big issue if you use the cable approach described by @Veggie Dave, I've been doing exactly that for years now (after getting burned once).

The big issue will be once wireless systems become so abundant that you have more than 6 on the same stage or you have a mix of different brands that are not communicating with each other and then interfere.
But there is no point in going wireless for the lead vocalist who is getting so drunk after the first set that he needs a chair anyway. Or the bass player standing in front of his stack. Etc...
 
Not having ever set-up a stage for wireless...

None the less, two thoughts.
the nu-x says it's using 2.4 GHz IMS - same as most popular WiFi devices.
1/ these days most WiFi routers, phones etc. Can use the 5Ghz band. If you could get everyone on stage onto 5Ghz and switch off the 2.5 radio on the router, you'd probably be doing yourself a favour.

2/ If I was setting up a stage I'd consider putting the WiFi router quite high up so that at least it's transmitter was further away. As well as it having better line of site (even more so for 5Ghz) to on-stage gadgets.

Basically spot on!

If you're running a router then the dual routers are definitely the way to go. If you've also got someone in the auditorium mixing for you (using a mixer on the stage via tablet/laptop - quite common these days) then you want a directional dual channel router.

And get that router above stage level if at all possible. There's usually somewhere to put it if you remembered to also buy nice, long CAT and power cables.
 
I was assuming there's a WiFi router just for the stage and any front of house equipment is separate.. indeed, if you are visiting a venue, getting equipment - pads, phones for controlling personal mixes etc. Onto the venues network seems dodgy to me.
Basically spot on!

If you're running a router then the dual routers are definitely the way to go. If you've also got someone in the auditorium mixing for you (using a mixer on the stage via tablet/laptop - quite common these days) then you want a directional dual channel router.

And get that router above stage level if at all possible. There's usually somewhere to put it if you remembered to also buy nice, long CAT and power cables.
True but 90+% of the venues I have played have music as an embellishment and not their main source of income. Off the top of my head, I know maybe one out of 100 that may have dual routers. Dual equipment = dual the cost and 2^2 the maintenance issues and possible failure points.

Most venues around here do not have a house PA, it is up to the band to bring it, along with their own sound guy.
 
Sure. Horses for courses.
A background music group isn't a full stage show which isn't a stadium show.

The point, I guess, is that spectrum management is a thing and the performers have - may need to have - some control over it...
 
True but 90+% of the venues I have played have music as an embellishment and not their main source of income. Off the top of my head, I know maybe one out of 100 that may have dual routers. Dual equipment = dual the cost and 2^2 the maintenance issues and possible failure points.

Most venues around here do not have a house PA, it is up to the band to bring it, along with their own sound guy.

This has nothing to do with the venue's Wi-Fi.

These days, it's very common for musicians to be able to control their personal monitor mix using an app on their phone or tablet. To do this, the mixer/stage box has its own router (sometimes built in, usually a separate router plugged into it) that the phone/tablet logs in to.

This is an example image of one of the apps I run for the Spandau show. This app runs on your phone, which is logged onto the mixer's Wi-Fi network, that allows each member of the band to mix their own IEM:
app.webp


The FoH sound engineer can also log into the mixer's router to control the entire show. That app is rather more complex than the one pictured above.

Because there are usually so many competing Wi-Fi networks at venues, bands running their own sound/monitor mixes really should stick with dual routers to lessen the probability of connection issues.

If you're only using the in-house PA, then you get what your given, over which you have basically no control.
 
This has nothing to do with the venue's Wi-Fi.

These days, it's very common for musicians to be able to control their personal monitor mix using an app on their phone or tablet. To do this, the mixer/stage box has its own router (sometimes built in, usually a separate router plugged into it) that the phone/tablet logs in to.

This is an example image of one of the apps I run for the Spandau show. This app runs on your phone, which is logged onto the mixer's Wi-Fi network, that allows each member of the band to mix their own IEM:
View attachment 27649

The FoH sound engineer can also log into the mixer's router to control the entire show. That app is rather more complex than the one pictured above.

Because there are usually so many competing Wi-Fi networks at venues, bands running their own sound/monitor mixes really should stick with dual routers to lessen the probability of connection issues.

If you're only using the in-house PA, then you get what your given, over which you have basically no control.
Tell you the truth, I have never played with a band where we had IEMs, what you are talking about is about 5 levels above what the local shows / venues are about. I think it's very cool, but over here you are lucky if you have a stage that's larger than 8 square meters.

Of course, there are some venues that are more advanced but I would be hard pressed to name more than one in a 50 mile radius.

In other words, we are looking at this subject from two very different perspectives. AFAIK, there is one venue in town that could host the Spandau show but yea, I get it where you are coming from.
 
This is an example image of one of the apps I run for the Spandau show. This app runs on your phone, which is logged onto the mixer's Wi-Fi network, that allows each member of the band to mix their own IEM:
Dave - would you be willing to share details of the setup for this - mixers, IEMs, apps etc. ?

The function band I play in has a small part of this tech (WiFi routers, x-air mixers) but only one set of IEMs and no personal controls. Your option sounds very interesting...
 
Dave - would you be willing to share details of the setup for this - mixers, IEMs, apps etc. ?

The function band I play in has a small part of this tech (WiFi routers, x-air mixers) but only one set of IEMs and no personal controls. Your option sounds very interesting...

You should be able to plug your personal IEM transmitter into one of the X Air's Aux outputs (as long as you're not using the X12 as that only has 2 AUX outs) and then control it using their monitor app:
 
As there's been a fair bit of talk about using wireless mics/systems recently, I thought some of you might find it useful to read my experiences over the last two years of teching a 9-piece band that's predominantly wireless.

This is a very, very basic guide to using wireless systems on stage, that's aimed at smaller shows/bands who are most likely using all sorts of kit that's owned by the individual musicians, rather than a big production with an integrated system.

To cut a long story short (😉) ; transmitters, receivers, Wi-Fi routers and Induction Hearing Loops don't mix.

If you're running wireless mics and wireless IEMs then you need to keep the two systems physically separate. You can get away with a gap of just 60cm between a mic receiver and an IEM transmitter. However, if at all possible, 1m or more is preferable - especially as the number of receivers and transmitters increases.

Line of sight also reduces potential interference issues massively. By this I mean there should be as few obstacles between the receiver and transmitter as possible. For example, if your sax mic uses a 'belt' transmitter, you put that transmitter on your body so that it can physically see the receiver. Your body is incredibly good at absorbing both analogue and digital signals. So are other musicians on that stage.

If you have your mic transmitter on the horn itself, then removing as many physical obstacles between it and the receiver is even more important. Reducing the distance between the two can really lower potential issues.

Wi-Fi routers need to be kept away from any other wireless equipment no matter whether those systems are analogue or digital. If you're using IEM that allows each band member to control their own mix then that router should also be positioned so that there are as few physical obstacles between it and the musicians as possible. Venues, theatres etc. all have internal Wi-Fi systems (often multiple systems) these days, that are more than capable of interfering with your Wi-Fi signal.

Also check to see if the venue you're playing is using an Induction Hearing Loop. If they are, get them to turn it off if possible - and assuming your show doesn't need it. Induction loops can cause uncontrollable feedback, even on a completely silent stage.

Dialling in the system:
This really should be done either during a normal rehearsal or during a tech rehearsal. If at all possible, don't leave this part until you're at the venue, just in case. You never know what's going to happen during soundcheck at the best of times, so don't take the chance.

Start with everything other than the Wi-Fi router (if you're using one) turned off. Decide whose wireless system is the most important (your criteria for this will be subjective to your specific band/show) and turn it on. Make sure it's working perfectly. If there's an issue, change its channel until it works faultlessly. If this doesn't help, move the system further away from the router and start again. Once you're happy, move on to the next system and repeat. You should be able to get the whole band up and running really (or, at least, pretty) quickly. Once your set-up is solid, it should work perfectly every time from that point on. This tech rehearsal also means you can work out where everything is going to physically go, too. Keep everything as neat and repeatable as possible and you're good to go.

If you're using a system where the receiver plugs directly into the mixer/stage box (it looks like a large XLR connector, such as the Nu-X system), plug the receiver into an XLR cable first and plug that into the mixer. You can't assume there's enough space to plug the receiver into the mixer/stage box. This type of system is also very popular with guitarists, so your receiver may not be the only one, which potentially leaves even less space. Depending where the mixer/stage box is, there could also be numerous physical obstacles between you and it. Use an XLR cable (or have one ready to go, just in case) and you instantly remove all these issues. No problem with plugging it in, no problems with line of sight as you can put the receiver anywhere you want.

I know this is a lot of text, but it's a lot of words to describe something that shouldn't take any time at all to actually do when you're setting up on stage (or in the rehearsal room).
Wow ! Most helpful . thank you for sharing your experience. Charlie
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,061
Messages
578,378
Members
8,129
Latest member
Bartman
Back
Top Bottom