Tech/maintenance Re-using pads?

DavidUK

Well-Known Member
Messages
8,133
Location
Near Evesham, Worcestershire
I bought an old Karl Meyer (Orsi) tenor and have used it as a donor to supply various parts (hinge rods, pivot screws, guard, key) to my Orsi Pennsylvania tenor. The scrappy and now scrap KM body has recently been utilised to try different bare brass finishes (see other thread).

Anyhoo... the Penn's pads look original whereas the scrap KM's, still in its key work, are very new with few showing any sign of use or seat impressions. The seller did say she'd had it re-padded but it never played properly afterwards. I could immediately see none of the bottom stack pads closed properly so this confirms she wouldn't have played it much as it wouldn't play!
I don't know what make the pads are. I'm guessing cheap as the tech work may have been amateur/bodged for it not to work. All key cups appear to be the same sizes on both horns so the pads are interchangeable.
So, can I re-use them and swap them out to the recipient horn?
Seems a shame to waste them. I'm trying to harvest as many bits from the dead horn as I can.

When I stripped my YAS-21 pads out recently I tried heating a couple of cup backs with my new hot air torch to remove the pads without damaging them. This I could do OK but the glue/shellac on the back of the pad pulls away from the cup in spikes and then sets in that pattern. This would make them tricky to re-use but I'm guessing some of you have tried this money saving exercise before so may have found it possible, or a waste of time?

If it IS possible, how did you do it and get around the spikey gluey pad backs?

Thanks for any insight.
 
Reusing a possibly cheap used pad from another instrument with an adhesive on the back I am not familiar with is not on the top of a list of things I would do. Besides, the cost of a new pad is negligible in the scope of work and materials required to do a proper overhaul.
 
I wouldn't use pads with even a faint seal impression. Economical re-use of a pad may only take a short period of time. In that time you have to make a full quality analisis of that pad and remove it in such a way that it is still usable. Pads that have no seal impression and qualify after this quality analisis are too rare to make an economic impact.
 
Cheap pads work fine first time round. Maybe not for as long as an expensive pad.
The cost being in the labour, most players want something that lasts and maintains its performance.
Doing it myself I don't mind swapping out worn out or poorly performing pads.
Playing 7 days a week outside, in all weather's, shortens the life of the best pads.
In my opinion a new cheap pad will perform better than an expensive used one.
A cheap used pad is for the bin.
 
The first one out of the box of displaced keys was this one, flat reflector...

20230122_152147.jpg


...fortunately not a good fit, I inserted a small flat head screwdriver into the gap, no heat, and it easily popped out...

20230122_152223.jpg


...feint impression noted, I flipped it over...

20230122_152207.jpg


That's got to be worth saving, if only in the "first aid" box? I'll try a few more...
 
Still, when it takes just a few minutes to make a new pad from scratch, why save pads with deep impressions anyhow?...

20230122_160641.webp


For a vintage horn, the backing disc serves as a flat reflector, with a ring of synthetic sealing material.

I'll make a whole new set and keep the good Pisoni ones for emergencies.

:thumb:
 
The unmarked Pisoni ones are, I agree, worth saving in the first aid box. The ones top right and bottom left in the last pic have been so far off centre that they're probably not worth trying.
 
I keep a box of pads like that to use for leather, felt, resonators, dry fitting, and flinging at the cats.

The dog eats them, so I'll only throw the ones with plastic resos at him.

t
waste not, have a storage problem.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,073
Messages
578,615
Members
8,133
Latest member
walthang
Back
Top Bottom