Saxophones Pork Tales: Saxophone Repair DIY Adventures.

Life around the barn.
Tales from a pig that likes to stick his nose into everything.

Paint that S. How difficult could it be ?
1747869014621.webp


1) Search the net.
2) Find the color.
3) Order color.
4) Study task on University of YouTube, aka; For destruction by DYI presented by pro tech.
1747869824677.webp



1747869909688.webp


Do the cleaning & prep.
1747870236970.webp


Paint and cleanup / detail the edges with hard cotton swabs. Sounds easy……:confused:
1747870401847.webp


Yeah tha guy Matt makes it look easy.
Anyone remember your first experience cooking bacon crispy while still in the frying pan !
 
You got off light.
Bank of England calculator shows £170 in 1934 is £10,921.40 in 2026.
Mmm...maybe. (opens other tabs to run numbers...)

In 1934 one pound sterling was worth a whopping five US dollars.😱 (US Great Depression started in 1929)

The Imperial tenor would have set you back £34 in 1934 or £2184 in today's money. At the current exchange rate that's $2899.

I think your inflation has been worse over the years but the exchange rate still gives you the advantage.
 
I took the crook brace off my Typewriter to use as a pattern. I checked fit to the Imperial neck. It’s really close but not exact. A little final hand fitting is expected.
Pattern secured firmly on plate with mini “C” clamps. I then scribed a line around the part with a hard point scribe. Make a mark and move a clamp if needed. Going to be good challenge cutting the part out.
IMG_6168.webp
IMG_6169.webp
IMG_6170.webp
 
Well the Typewriter neck needs some attention too. Has just a wee little bit of pulldown. The tenon was likely re-soldered at some point. The area where the brace attaches above the tenon had a big glob of solder. Taking the brace off was needed. Additional benefit, a pattern to make a spare😉.

Funny thing and reason for this picture below. The braces are not positioned perfectly inline on center. 🤦‍♂️
It’s always something small that bites you.
1792188996366.webp


I needed to clean off all the old solder on the Imperial crook. This to test fit the bit sample.
That’s when I discovered neither were centered 🤦‍♂️🤦‍♂️
1792189780952.webp


Make it straight and have a shiny spot, or make it original and crooked. Both options include a brace that’s new….unless there’s a way to add 92 years of patina this week 🤣
 
Body dent work, soldering repair, tone holes leveled (yes on bent body’s it happens. Usually around the bell brace & bow) springs removed, post alignment, post fitting and key fit is done ✅

21 springs and I only have 8 the correct length & diameter. $190 in spring inventory ordered at 01:34 AM🤣
IMG_6174.webp


The spring caddy is 1” thick foam with hostage style notes attached with tape. Old spring removed is placed by measurement. Replacement/ spares to outside. As played I note Right, Middle(back) and Left sides. Then from reciever down the pillar position and measurements.
IMG_6175.webp


Also while doing a bit of midnight shopping at Macy’s I ordered some needed pads…
The Bb pad is big for tenor @ 56mm. That’s stepping into baritone sizes. Tenor is usually less that 53mm with 50mm being most common. I stock up to 53mm. Like 25 qty. 50, 50.5, 51, only two on 51.5, 52, 52.5, 53mm
@ $7 each there’s no reason to have pads around for the once a year oddball….add $42 to order for 6 pads. 3 @ 53mm 2@ 56mm. That’s with a hole, no booster.
Ya think theses are old pads 🤪. No cardboard back. No shellac. Pop testing these sound like a baseball hitting a catchers mitt….thud.
L, 50mm. Center,40mm, R, 56mm
IMG_6176.webp


Below.
These are size stickers in 32’nds. 63/32=50mm, 57/32=40mm
Also notice the installation style. Shellac liquified in denatured alcohol brushed into cup. Pad placed then gently heated over an open flame to evaporate the alcohol and set. Zero floating. No wonder so many factories burnt down.
1792193662566.webp
 
Many of you know I work on vintage and classic cars too. Today I reflected on a past car experience. A 1951 Ford 2dr sedan to be exact. This was 20+ years ago. The owner was having issues with the doors rattling and wind noise.
Without even seeing the car. I knew the weather stripping seals around the doors was likely the cause. Door latches/ catches second.
As the second owner she admitted “my husband’s notes don’t show the parts ever being serviced or changed”. A kit was ordered. A simple task to remove and replace. A house call with a few tools in hand.
I had never seen the car before. Met the lady at a car club outings several times. Meeting one mid morning sunny Wednesday. She greeted me with hot coffee and a homemade cherry tart. Small details you never forget.
I reviewed the kit parts as good and started the task as she looked on. I was in my repair mindset zone…
I heard her say “What’s wrong!!!”. I looked up and said Huh ? She replied that I said “WOW look at THAT !”…
I had pulled away some trim / weather stripping that had been in place since 1951. The paint underside was factory perfect ! Absolutely as it left the Ford factory perfect. Small but a glimpse of how beautiful this was at new.

Today working on the Martin Imperial reminded me of that day. Removing a small bit of cork from the front F fork. This most likely placed at the factory in 1934. Removed today and showed the original beautiful finish underneath for the first time in 92 years. 17 years older than the Ford sedan.
1792224840960.webp


1792224910636.webp
 
Onwards !
Keep your parts / spares organized !! It’s not that difficult. Just pick a method that’s easy to remember.
1792226244197.webp


Who cares if you use a bit of plastic off your motorbike outfit or Egyptian hieroglyphics to name the bits !!!
What matters is getting the bits back to their original positions 👍
IMG_6190.webp
 
This staying organised bit is my bete noir (I had to check that spelling!). It's a confidence knocker, because while one is looking for the fault, 50% or more of one's brain is shouting 'are you sure you can remember where all these bits go?'. Thanks for the tips on keeping it all together, I am going to try using some of them.

Regarding the neck brace - here, that would get roughed-out on a bandsaw and then trimmed back to the line on a belt linisher. I'm not sure linishers are really meant to be used for fairly heavy shaping operations, but they're really handy for it in my experience, especially if you have some belt with a rigid support behind it, and some open that you can push the part into for curves etc. My dad would probably sniff a bit at me and reach for the files.
 
Last edited:
This staying organised bit is my bete noir (I had to check that spelling!). It's a confidence knocker, because while one is looking for the fault, 50% or more of one's brain is shouting 'are you sure you can remember where all these bits go?'. Thanks for the tips on keeping it all together, I am going to try using some of them.
I’ve taken enough cars, motorcycles and watches apart that taught me painful lessons. Bolts in a bucket, wiring unmarked. Maybe I’ll remember tomorrow, but six months from now and twenty projects in between? Nope.
That screw caddy was once a pallet. The purple plastic. Look at the front panel of my MX sidecar 🤣, yeah scraps !
Regarding the neck brace - here, that would get roughed-out on a bandsaw and then trimmed back to the line on a belt linisher. I'm not sure linishers are really meant to be used for fairly heavy shaping operations, but they're really handy for it in my experience, especially if you have some belt with a rigid support behind it, and some open that you can push the part into for curves etc. My dad would probably sniff a bit at me and reach for the files.
Planning on using the neighbors scroll saw. Clean up with a metal burr in pillar drill. Then switch to sanding drum bit from Dremel kit. Next I’ll drop it on floor, kick around a bit and solder on. Paint on a coat of Amber shellac then burn it some🤣
 
Pads from the Imperial. Looks like three different services.

The top two rows are same make but different handwriting. Still both were installed with white glue or ??
Gooey stuff that didn’t really melt with heat, but dissolved with heat and isopropyl alcohol.
1792410594674.webp

IMG_6192.webp
IMG_3926.webp


The bottom row is definitely the older group.
1792304136555.webp


@turf3 the cork lap joint overlap was almost 13mm wide 🤦‍♂️
1792304478531.webp
 
Last edited:
Hey, maybe that bucket of bolts will come in handy - drop the part in there, tie it to your sidecar and run around with it bouncing about for a few weeks. (But - I might forget I had put it in there...).
Loaded and ready !
FWIW, those two 1-3/8” nuts I have no idea what they went to. No friends or customers ever came back to complain that something was loose 😬.
1792377192910.webp
 
At our museum we managed to loose a nut (1 of 8) which was 6" AF. We reckon someone nicked it to use it as a door stop 🙂 I don't mind sorting screws, nuts, bolts and all that, though. I can already see some dimensions of order along which to reduce the entropy in that bucket.
 
Edit: this gives me an opportunity to share something from 'The Ladybird Book of the Shed' - which is a recent, quite funny spoof of a series of really lovely children's books which were popular when I was a kid, 50 years ago. The top imagine shows 2 'real' titles from long ago, and three modern joke ones which use the (amazing, IMV) hyper-real 'my Mum's got that jumper' original artwork, with new text in the original style. I think the picture in the lower one was probably from a 'Men at Work' book, featuring a printer. The text raised a smile!
S7000221.webp
S7000223.webp
 
I think the picture in the lower one was probably from a 'Men at Work' book, featuring a printer. The text raised a smile!
That’s funny ! Yep that’s definitely a type case and a “stick” in his hand. The reading copy in front of him.
I guess back in the day men spent their holidays sorting massive hardware as a hobby 🤪
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,063
Messages
578,433
Members
8,130
Latest member
tommyliehe
Back
Top Bottom