Saxophones MkVI vs. MkVII baritone measurements.

DavidUK

Well-Known Member
Messages
8,133
Location
Near Evesham, Worcestershire
A while back, when I bought my MkVII bari, Pete Hales (thesaxinfo), @helen and @JayeNM were interested in comparing measurements between a MkVI and my MkVII which looks identical to a MkVI.

I'll get around to the measuring very shortly but I wondered if anyone here has a MkVI bari and is close-ish by to me so as to do a side by side comparison?

A long shot, but I thought I'd ask. I'm near Lutterworth, Leics.

Thanks for any help.
 
David -

Apologies for the delay, busy times... I have a Mk VI low A baritone, and I'm based in Hull. I'd be interested in doing this, and having a look at your new pads as well if we can sort out a time/date.

I've got a few busy weeks coming up, but we may be able to come up with something if it's not too urgent.

I also have an ongoing project horn that I would be very interested in trial fitting with your pads at some point...
 
Please publish your results 🙂
I've sent Noel the measurement requirements @JayeNM sent me a while ago. We'll each try and do the same measurements soon as an interim solution (in case mine sells!) and then hope to meet up in the next few months to do a side by side comparison, with photos ideally.

I don't think JayeNM would mind if I repeated the suggested measurements here:

"OK, so you want to take some measurements along the body tube, the diameter of the body tube. Exterior diameters of the tube, using calpers.
Start at the bottom of the ferrule where the upper bow attaches to the straight tube. that is #1

2) go down to maybe the bis key hole, and center the calipers on the center of the hole and take a tube diameter measurement there. If the calipers are obstructed by the keywork, pick a different hole. The A, the G for example.

3) do the same thing again on lower stack, either the D hole or E hole.

4) do the same thing you did in 1) except measure at the bottom of the ferrule which attaches the body tube to bow.

5) using a tape or long rule, measure the LENGTH of the body tube from the upper to lower ferrules.

6) stand the horn up and measure the distance from the bottom of the bow to the bottom of the bow ferrules. I hope the bowguards on each horn look of similar dimension, here.

7) get the calipers in between the vertical legs of the bow and measure the distance between the surfaces of the bow legs (this is to determine if bow curvature is the same or not).

8) back to the upper bow, measure the diameter of the bow tube/elbow at the very top of the bow.

9) measure the upper bow at the bottom-most curve of the upper bow, near the water key

10) Measure the neck receiver diameter opening"


I think I can follow this but until I have the horn in front of me...

If anyone needs any other measurements, please post.

Once done, we'll publish on this thread for each horn.
 
OK, I've had a go now that the baritone and I are in the same building again... I've rounded a bit as my calipers aren't the best and my sax isn't entirely as it left the factory... see notes below

1) Just under the ferrule - 37.3mm / 1.47"

2) Between the bis tone hole and the pillar just below it - 45.5mm / 1.79"

3) Near the E hole, between the aux F# and low D# pillars - 63.7mm / 2.51"

4) Just under the ferrule - 68.4mm / 2.69"

5) 78.5cm / 30.5" between the ferrules

6) Back: 13.3cm / 5 7/32"; Front: 19.5cm / 7 11/16"

7) 38.3mm / 1.51"

8) Roughly 38mm / 1.5" - my pigtail is a bit square at this point

9) Tube here is oval, but average seems to be 25.4mm / 1"

10) 22.6mm / 0.89"

Apologies for any mistakes or mistranslations from metric to English/American, and also apologies for owning a battered Mk VI that isn't quite the right shape!
 
OK, I've had a go now that the baritone and I are in the same building again... I've rounded a bit as my calipers aren't the best and my sax isn't entirely as it left the factory... see notes below

1) Just under the ferrule - 37.3mm / 1.47"

2) Between the bis tone hole and the pillar just below it - 45.5mm / 1.79"

3) Near the E hole, between the aux F# and low D# pillars - 63.7mm / 2.51"

4) Just under the ferrule - 68.4mm / 2.69"

5) 78.5cm / 30.5" between the ferrules

6) Back: 13.3cm / 5 7/32"; Front: 19.5cm / 7 11/16"

7) 38.3mm / 1.51"

8) Roughly 38mm / 1.5" - my pigtail is a bit square at this point

9) Tube here is oval, but average seems to be 25.4mm / 1"

10) 22.6mm / 0.89"

Apologies for any mistakes or mistranslations from metric to English/American, and also apologies for owning a battered Mk VI that isn't quite the right shape!
OK, I've done the MkVII now, as under, Joel's measurements in brackets:

1)* Tube, just under the ferrule - 31.8mm* (Joel's MkVI - 37.3mm)
2) At centre of bis home 44.4. (Joel's measurement slightly lower appears correct)
3) Centre of E hole - 63.5mm (Joel's 63.7mm). NB. I did D too at 66.5mm
4) Under bottom ferrule - 68.5mm (Joel's 68.4mm)
5) Between ferrules - 78.6cm (Joel's 78.5)
6) Rear - 13.4cm. Front - 19.5cm (Joel's 13.3mm/19.5mm)
7) Between bow legs - 38.3mm (Joel's 38.3mm)
8) Top of upper bow - 35.5mm (Joel's 38mm).
9) Bottom of upper bow - 25.5mm (Joel's 25.4mm)
10) Neck receiver - 22.4mm (Joel's 22.6mm) & neck tenon, to check, 22.3mm

Notes on significant differences between MkVI & MkVII:
Overall the measurements match up very closely, within 0.1/0.2mm, apart from these two...

1) 5.5mm difference is waaaay different. I took a photo...

20241111_144646.webp

8) 2.5mm difference. Joel says his is damaged here.
 
Last edited:
Who's Joel? 😏

I think we've measured different places for #1 - I think you've measured under the ferrule joining the top bow to the down tube of the pigtail? Is that right?

I measured under the joint of the top bow to the main body tube. I'll re-measured as you've done later on.

And yes, measurement #8 on mine is very approximate, as at some point prior to my ownership the pigtail got quite squished, so the tube there is a short of partially square cylinder. Still plays great though 🙂
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,063
Messages
578,433
Members
8,130
Latest member
tommyliehe
Back
Top Bottom