Tech/maintenance Metal Clarinet service repad

Thanks for sharing the products experience.
I’m not overly fond of Asian pot luck parts.
A half gallon of milk here is now $7/ £6
The set cost about $17 £15. Good quality.
These pads came from Instrument Clinic. I’ve use the pads before with good results. Music Medic too. The number one issue was the new adhesive pellets. Expanding and shrinking to size of cup was crazy. Reheated way to many times to get good fit.
Dang, a gallon of milk here in Indiana is $2.96. / £2.76. I reckon those happy California cows are expensive.
1664325952467.webp
 
Got a Bettoney in for an action rebuild.
Having 'great fun' tightening up the free play on the upper stack keys. With keywork this small you're nearly always going to run into issues with being able to get swedging pliers on some of the keys - and it's always sod's law that these areas are among the most important in terms of the integrity of the action...at least if you want to have even half a hope of accurately regulating it.

Bettoney wobbly action.webp


So the trick is to chuck the swedging pliers back on the rack and go with oversizing the rod screws. The also deals with wear in the pillars are the same time and brings the action 'back to new' (and quite probably better).
Easy-peasy, right?
Almost. With compound key arrangements like this you're going to run into torsion twist from the tooling - which means having to realign 'split keys'. This stack is made up of a pair of split keys - so once you've reamed out the key barrels you them have to align each end of the keys so that the rod screw slides through smoothly. That can take you about 30-60 minutes of toing-and-froing as you try to adjust the angle of barrels until they line up. And no, you can't just get them close and then lap them in, as that would effectively add wear.

Bettoney fixed action.webp


Here's the rebuilt stack - all nice and snug...and not a tooling mark to be seen (at least none that I've made).
This'll make a huge difference to the feel and response of the clarinet. Tweaking that adjusting screw will regulate the action perfectly, with none of the approximate feel it had before.
 
I'm having to do the whole lot.
Degree angle?

Not sure if it's a newer model rather than a step up in the range. It's also a full Boehm system.
Well you probably needed practice making left-hand threads😉

yes the angle of pivot point.
1664572443030.png

After doing some net surfing I do see some differences.
It appears the more upscale models do have some obvious enhancements. For starters the tone holes appear to be flanged. The ones on my unit are a straight thick chimney.
BE2ED3EA-F0D6-47F7-8F3C-B358AC45869C.jpeg

This lug with adjustment screw for setting the regulation upper/ lower stack.….nonexistent on my model🙁
2550A576-82F8-440E-8C53-580893EBE57C.jpeg

Good news is that I have usable casting here. Just need to drill-tap and install set screw here.
F7F5C097-343B-4C53-BD05-C5777E8F591E.jpeg

A723A7A0-B816-4AA1-89A5-07603A4F15D9.webp
 
Last edited:
Not sure what the angle is because I usually set it slightly large and then bring it in by hand - unless I'm bushing the point screw barrels...in which case it's determined by the angle of the reamer.
You almost always have to 'jiggle' the angle on pointed rod screws or adjust the thread relief to get a snug fit - and it pays to leave the fit ever so slightly large so that there's scope for future adjustment at the other end of the point screw mounted key.

This clarinet has the flanged toneholes, and flute-style screws on the lower pads.
 
Not sure what the angle is because I usually set it slightly large and then bring it in by hand - unless I'm bushing the point screw barrels...in which case it's determined by the angle of the reamer.
You almost always have to 'jiggle' the angle on pointed rod screws or adjust the thread relief to get a snug fit - and it pays to leave the fit ever so slightly large so that there's scope for future adjustment at the other end of the point screw mounted key.

This clarinet has the flanged toneholes, and flute-style screws on the lower pads.
Understood. The configuration of the rod/pivot can bring about some interesting issues. I’m good with ”hand fit”

Is “flanged“ the proper description of this type of tone hole? It’s the best I could come up with.


I’m sure there’s more than one clarinet site that’s loaded with information. My scheduled reading time is already booked until 2038.
Although I did some off schedule reading here. Very interesting history.
 
This is quite a detailed tutorial on metal body clarinet repair, @PigSquealer , thanks for taking all the time and trouble to document how you overcame various issues, as well as tips on things to look out for. Also, all the other inputs were educational contributions.
 
This is quite a detailed tutorial on metal body clarinet repair, @PigSquealer , thanks for taking all the time and trouble to document how you overcame various issues, as well as tips on things to look out for. Also, all the other inputs were educational contributions.
Yes, thanks All. I appreciate the knowledge and technical help too.
 
Could we ask where one may obtain these? Just interested.
 
Modelling supply shops are great for dinky doo tools.
Try not to get distracted by the models for sale.
Oh look! A radio controlled submarine. 😛
Submarine sales recently took a dive. Buyers not returning from weekend outings, or something of that nature.
I guess it’s been a while since you’ve been out of the house. Try the next aisle over. Sailboats, technically a wind instrument. Let us know when you’re headed off. After three hours a GAS brass rescue team will be dispatched.
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,072
Messages
578,571
Members
8,133
Latest member
walthang
Back
Top Bottom