Tech/maintenance Is there a screw missing in the octave mech?

Messages
72
Location
Barnstaple
Dear Forum,

Today I noticed that the octave D stopped working. Then with some more playing the octave mech started behaving erratically and behild there seems to be a screw missing in the first bit / pivot / hingy bit that comes after the octave key. (Red arrow)

It causes the mech to shift laterally where it, I guess, should rotate in line with the rod. (See blue circle)

Any chance I am correct in this?
Where would I get a screw (which type) that solves the problem?

Thanks in advance!
Best wishes,

J.

IMG_0550.jpeg
IMG_0551.jpeg
 
Yes the screw is missing. Likey unscrewed itself and dropped out.

This is a good reason to oil your horn from time to time, you get a chance to look at this kind of stuff. Probably took several weeks if not months to back all the way out. Also, keeping your mechanism clean and oiled helps prevent this kind of problem. Dirt and caked oil collects in the hinge tube and it binds on the screw, slowy working its way out.

Any good repair tech would be able to replace that screw. If we knew the make and model of the saxophone, it might be possible to get a replacement screw from the manufacturer or a supplier of woodwind repair items. But a good tech will be quicker.
 
Vote:
Upvote 0
Vote:
Upvote 0
There's a long rod screw that runs down the entire length of that group of keys (known as the octave mechanism), and it's quite common for it to slowly work its way out over a period of time (for various reasons). It's unlikely to have fallen out else the entire mech would have fallen off the horn.
If you take a look at the other end of the mech you'll probably see the head of the screw sticking out of the pillar. It just needs to be screwed back in.
 
Vote:
Upvote 0
“Inspired” by this, Now I’ve looked at my Tenor more closely and saw that the pin is quite far away from my octave crook key. Pin straight. Is this a matter of bending the crook key as per @Stephen Howard ‘s book?

Mech opens the crook valve this far but only in ideal position. gap is about 3-5mm. In not ideal position the pad closes automatically despite octave key being depressed.
Thanks in advance.

Cheers!


IMG_0554.webp
IMG_0555.webp
IMG_0557.webp
 
Vote:
Upvote 0
“Inspired” by this, Now I’ve looked at my Tenor more closely and saw that the pin is quite far away from my octave crook key. Pin straight. Is this a matter of bending the crook key as per @Stephen Howard ‘s book?

Mech opens the crook valve this far but only in ideal position. gap is about 3-5mm. In not ideal position the pad closes automatically despite octave key being depressed.
Thanks in advance.

Cheers!
Yep - but the ring key looks a bit distorted, so you might not achieve the full range of movement in some crook positions.

More details here:

 
Vote:
Upvote 0
On the near todo list. Thanks! No offence taken!
Personally I'd suggest an alternative to a cheap precision screwdriver set. Have a look at the screws on your sax. There are probably only two or three sizes. I'd suggest buying a small number of decent screwdrivers, you don't need to spend a fortune, but ones from a good brand such as Wera Kraftform are about a fiver each. Two or three of those would probably be all you need, would last well, be less likely to damage screws and be nicer to use than a cheapo set.
 
Vote:
Upvote 0
Whatever you go for, it's very important to use the correct size screwdrivers on saxophones. It's easy to damage a screw head using a driver that's too small, or damage the finish on parts if your screwdriver is too broad and overhangs the sides of the slot.

As previously said -you'll probably only need a few. But choose carefully, perhaps one of the experienced technicians on here can advise as to what sizes are best suited to your make and model of saxophone
 
Vote:
Upvote 0
Whatever you go for, it's very important to use the correct size screwdrivers on saxophones. It's easy to damage a screw head using a driver that's too small, or damage the finish on parts if your screwdriver is too broad and overhangs the sides of the slot.

As previously said -you'll probably only need a few. But choose carefully, perhaps one of the experienced technicians on here can advise as to what sizes are best suited to your make and model of saxophone
That would be fab and great suggestion. It is a yas-32 purple logo.

Thanks!
 
Last edited:
Vote:
Upvote 0
I like wera tools. Sounds like a good shout
Whatever brand you buy ;
Make sure the tip is not too wide causing damage to the post hole.
Make sure the angle of the tip is not too steep. This will spread the end of a hinge rod causing damage, or potentially wedging it into the post.
it’s amazing how much misery a stupid screwdriver can cause you !
B62F1EF2-CADB-4AAE-A99B-15A84C2288FC.webp
DECFFB1B-BCC7-4320-A1BA-92303E0D0669.webp
 
Vote:
Upvote 0
The reason I mentioned screwdrivers - because I didn't know how handy the OP is - comes from watching the other half tighten the screw on her old glasses with the tip of a knife and waving aside my offer of a watchmakers screwdriver... Not even checking if the knife tip is too wide or steep!
 
Vote:
Upvote 0

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,071
Messages
578,541
Members
8,132
Latest member
LouisJR
Back
Top Bottom