Tech/maintenance G a little sharp and wispy...

I think I can see a... tiny leak at G#...

20220502_161520.webp


...now, where's that 2mm thick washer...
 
That's not a tiny leak, that's absolutely MASSIVE! I'm amazed it plays at all. Makes me wonder about the rest of the repad. How in the world could that have been missed? I'd be tempted to take it to another tech if that's typical of his quality of work.
 
Temp fix solves the issue...

20220502_162649.jpg


...but is the permanent fix to beef up the worn cork on the lever. It has a typical wear indent, but the original thickness cork wouldn't be quite enough...

20220502_163114.jpg

That's not a tiny leak, that's absolutely MASSIVE! I'm amazed it plays at all. Makes me wonder about the rest of the repad. How in the world could that have been missed? I'd be tempted to take it to another tech if that's typical of his quality of work.
My little joke... tiny.
"His" work is mine. Please have a look at my DIY pad thread.
I'd gotten so far yesterday but had to break off to cook the roast lamb so had just used my (poor) eyesight without my leak light. I should have spotted this one of course... rushing.
I've been over the whole horn with the light now. Three or four other pads needed adjustment by 0.1mm or 0.2mm to remove leaks.
With these skinned pads which don't form a seat (rather than the TruSeal open cell neoprene predecessors which did) I can see a couple of tone holes are minutely off level. So I either need a more accommodating sealing material (closed cell, low compression set, neoprene is next to try) OR, like Jim Schmidt, I specify flat tone holes as a requirement of my system.
I'll try the neoprene first, but start looking more closely at good value tone hole files.
Remember, I'm just experimenting, and padding techniques are something I'm still learning. But at least there's no shellac, picks, irons, etc involved. Just nuts, bolts, washers...
 
Last edited:
I'm no tech, but looks to me like something just got bent. I'd simply bend it back. Otherwise, yes, you need a thicker cork there or a sleeve on the part it touches. In fact, it probably had one, but slipped off at some point.

I don't think doing a repad without shellac, picks, irons, etc. is the right approach. All those are very necessary.
 
In a case like that, where two arms bear on each other, the resilient material really ought to be on the one with the smaller radius. The round bar will chew up the cork on the long straight bar. I'd go corkless on the long arm and use heat shrink tubing on the round part, then make final adjustments by bending the long arm. Finally, put a little cork grease in between the two sliding elements.
 
I don't think doing a repad without shellac, picks, irons, etc. is the right approach. All those are very necessary.
You may have found it tricky to find the link to the video I did. Here's the correct post in the other thread so you can see what's changed from traditional materials:

 
You may have found it tricky to find the link to the video I did. Here's the correct post in the other thread so you can see what's changed from traditional materials:

Ahh, I see now. Very interesting idea. I can see the advantages and drawbacks discussed in the other thread. Maybe a bit more padding to account for uneven holes and a notch or two in the connecting parts to avoid rotation and lock the leveling in place after the initial installation.
 
The closed cell neoprene may do the trick... it's more accommodating of the unevenness but if the pad rotates off the off-centre tone hole rim the previous seat "heals" so as not to cause a leak where it crosses the previous seat.
However, the pads won't rotate other than when installed or re-installed so not a big issue.
That's the theory anyhow. I'll test it as soon as I can to see if it's the cover all solution.
 
In my experience using a "thicker" cork under the G# closing bar soon develops a groove which in turn changes the regulation and creates friction. What I prefer is to insert teflon tube on the "barrel" and to glue a thin piece of synthethic felt under the closing bar.

On most models, adjusting the G# can be done by holding the touch down and with the thumb of the other hand carefully pressing down on the closing bar. If you go too far, it can be raised by using a pad slick as a lever to lift it back. In some cases backing out the bumper felts on the low B and Bb to allow those keys to open a bit farther will provide the "lost motion" required between the "tabs" on the G# touch and the low B and C# keys. Of course the low C# will need to be adjusted to be on the same plane as the low B and Bb. Sometimes bending the tabs a small amount is possible, but doing that repeatedly can cause them to break off so extra caution should be taken with this adjustment. The LH table is a challenge to adjust because of the number of complex key relationships.
 
Last edited:

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,077
Messages
578,686
Members
8,136
Latest member
peterdehelegrote
Back
Top Bottom