Tech/maintenance Cleaning Fabric Inside Case

PiccoloPirate

Senior Member
Messages
1,205
Location
South Florida
Pictures of inside of old Buffet Clarinet case.
No odors but would like to clean the fabric.
Suggestions and I have a gas mask. 😵‍💫
Thanks
PP
FullSizeRender.jpeg

FullSizeRender.jpeg
 
Last edited:
Presumably it’s a sort of velvet and as well as cleaning it wants “fluffing up” where it has got compressed. What is underneath? These days there would be polystyrene or other plastic which would mean you need to be careful about any cleaner the could potentially dissolve it.

As an older case it might be foam rubber that you still need to be careful with unless you intend to replace that as well - which may actually be the best way to go. ie the whole hog. Which reminds me to call on our case refurbisher Mr @PigSquealer .
 
Last edited:
No telling what the cushion material is underneath. Pre 1970’s I often find a cotton batting filler. This has often collapsed from age and weight of the instrument against it. Dacron / polyester upholstery batting is the modern replacement.
Velvet fabric can be surface cleaned very gently. The silk ribbon is difficult to preserve. Those rip/tear very easily. You may wish to lift the upholstery where it is attached and remove it. Take it to somebody knowledgeable about fabric and have a backer put on it. Once that’s out I would vacuum everything best as possible. Then with low pressure compressed air give it a blast. Especially around the edges/nooks and crannies. Vacuum again. I use Woolite upholstery and carpet cleaner. Either using the attached brush for large flat areas or a soft brush for small cavities. DO check a small area for color fastness. Reds, blue & purple can fade with cleaners. Let the work air dry but not in direct sunlight. Sunlight will bleach these materials in the matter of an hour or two. Like a 75% color loss.
Vacuum with a soft brush attachment or final fluff with a soft brush.

Below.
Sorry I don’t have a before picture. There was a noticeable difference. The case had no noticeable odor. Afterwards it did have a nice fresh clean scent. I wouldn’t guarantee it but I have had no bad experiences storing silver instruments afterwards. This regarding tarnishing afterwards. Let the case stay open for at least a week before storing instrument inside.
1727299428757.jpeg

1727301059174.jpeg
 
Muchas gracias.
Not sure what the fiber between the fabric and cardboard is.
Woolite was also recommended by my seamstress sister and she said that since clarinets squeak and squawk, Dawn works on cleaning up Ducks.
Funny Lady.
Case was for a Bb clarinet, and at some point I'll remove the fabric from the lower half and redo it to fit the C.
Might use blue fabric for the bottom redo and green for the top. :mrcool
FullSizeRender.jpeg

IMG_3256.jpeg

Great locksmith shop nearby, so maybe they can make/find a key or show me what to make.
 
Last edited:
Gave the bottom of the case interior a squirt and scrub with Woolite and when it dried, I ripped it out.
Will most likely make a new bottom interior, to fit the C clarinet, from closed cell marine foam, that we use for high end boat cushions and motorcycle seats.
Color choice of velvet might now be a lavenderish/lilac.
Light purple haze?
FullSizeRender.jpeg

IMG_3496.jpeg
 
Last edited:
Will most likely make a new bottom interior, to fit the C clarinet, from closed cell marine foam, that we use for high end boat cushions and motorcycle seats.
Make sure the foam product contains no sulfur. The sulfur will turn all the silver parts black. Check the adhesives content too.
If I were doing this I would gut the interior. Lightly sand the surfaces and seal with coat of lacquer or sanding sealer. This step will help block the odor from returning.
Do a good test of all adhesives. Foam to case. Fabric to foam. Fabric to cardboard. Fabric to fabric. Fabric to case.
Use a bit of wood treated with the sealer for testing instead of actual case. Do this prior to treatment of case.
Be prepared for some surprising epic failures.
 
Thanks for the additional advice.
Had to button up, as a Blow named Milton was taking aim.
Landed North, but Tropical Storm conditions existed.
Did have access to tools to get a workable MP to play.
Stripped down the interior and decided to go with a yellow fabric, that will be ordered soon. Black and Yellow, from decades ago, when we handled loud and quiet.
Will make the foam/velvet bottom and top inserts removable for now.
Pic showing foams density and possible layout. Two gallons with little compression.
Left a bit of the old velvet on until the interior is cleaned up.
FullSizeRender.webp

IMG_3503.webp
 
Old pic of knife handle and case from early '70s.
First blade made from Ebony and in '78 made another blade with Carbon Fiber.
Left over from rudder post work, prior to Fastnet '79. They should have taken our advice from the experiments at Minneford.
FullSizeRender.webp



SgtVknives.webp
 
Anyway, have an early Buffet B12 on the way.
It has the modern version of the old case.
For out of tune duets with the
grandkids. 🥰
If we drive to Lake Tahoe, for a wedding next Summer, is it illegal to smuggle in ten gallons of Naphtha?
Bad boy
Bad boy
Watcha gonna do.
Retired Sheriffs in attendance. 😵‍💫


IMG_3777.webp
 
Last edited:
Be prepared for some surprising epic failures.
Your mentioning of surprising epic failure reminded me of this recent episode.

I attempted to repair a portion of sprayed popcorn ceiling that was separating from the drywall in the living room. Purchased a can of spray adhesive. It didn't work whilst spraying the 8 inch long gap from separation, pushing the popcorn matrix back only cracked it and it fell off.

Ended up scraping away all loose, which left me with 2 square feet of bare drywall to patch.

Your case repairs amaze me. Since I have no instruments of classic vintage value, (1965 plastic Vito clarinet, Boosey & Hawkes Edgware wood clarinet, Vito tenor sax) ended up buying aftermarket cases.

The early 1950's Beaugnier Vito Bari sax case was so far battered and well gone plus extremely musty in smell, tossed it and bought a modern moulded hard foam cloth covered "velvet" lined case.
 
Hopefully not an older one as it could contain asbestos fibres.
No asbestos as house was built some years after the ban. Am familiar though as I put together drawings and contract spec's for abating asbestos in old government buildings. In one case, tests indicated no asbestos in interior wall gypboard but was in the spackling compound used to bed the joints. That is, in the gov buildings, not the house.
 
Last edited:

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,064
Messages
578,434
Members
8,130
Latest member
tommyliehe
Back
Top Bottom