Tech/maintenance Thread sizes for Yamaha Alto... and others?

DavidUK

Well-Known Member
Messages
8,133
Location
Near Evesham, Worcestershire
Tech help please...

I'm putting together the YAS-21 I had wet soda blasted and I'd like to clean out the threads of any debris before assembling it. Can anyone tell me the thread sizes for rods and pivot screws please?

I make it four different ones, but I may have missed something so there could be more?:

Screenshot 2023-05-21 at 12.29.33.webp


NB. These parts have yet to be cleaned.

Apart from these, which I assume are all the same thread type, what other thread variants, e.g. BSP, metric, UNF, are commonly in use in saxophones and which ones would you need to have to be able to tackle any make/model which lands on your tech-ing bench?

Thanks for your help.
 
Sorry I no longer have a YAS-21, but I do have a YAS-23 parts horn in the shop. A rod's threads measured M2.5 x .45.
Both pivot screws and guard screws threads are M3 x .5. What I did when I started my shop was to buy the Ferree's tap and die sets in both standard and metric (expensive) and then added additional sizes as needed.

metric tap and die sets

standard tap and die sets
 
Weirder still... there seems to be US metric and UK metric threads?

Whoever heard of M1.7, M2.3 and M2.6? As here: https://www.saxontheweb.net/threads/yamaha-stack-screw-rod-thread-spec.83886/#post-808412

...and a little later, someone else says there isn't such a thing as M2.5: https://www.saxontheweb.net/threads/yamaha-stack-screw-rod-thread-spec.83886/#post-811976

News to me!

I just have these (including M2.5), plus M3:

20230521_213823.jpg


I've checked my M3 x 0.5 tap and the pitch IS 0.5mm. The pivot screw plainly isn't, but it is almost bang on 3mm diameter.

Is this like US gallons not being the same as UK gallons? Does metric differ across the continents?

I think I need... @Stephen Howard or @griff136 to help me decide if it's me, or the world, which has gone mad!

:w00t:
 
Last edited:
I have had a post deleted. Maybe my fault for just putting one word. The technical name for non standard threads is a bastard thread.

Yamaha seem to have their own pitch for standard diameters. I paid £5 for two genuine lyre screws.

A thread guage and a micrometer will reveal all.
 
The threads are likely JIS standard. That’s different than DIN or ISO metric standards. Huge difference depending on what you’re repairing. Japanese industrial standard on a Japanese motorcycle is hugely different than a Meridian Triumph and you certainly wouldn’t want to use those in a Ducati.
 
If you really want to study machinery and material applications get a machineries handbook used from eBay or Amazon. I picked this old one up for under $20. In the middle of the 2500 pages there’s some information about metric threads.…and then another 20 pages about all the different pitches.
8F7F9E48-3641-4403-BA95-E0643DDDDA5A.webp

4CA2E4E8-5D77-4ADA-AF9A-A232BBC1F8EB.webp
FA15CBA6-3485-40DB-BA67-BB1382D24248.webp
E809246B-EA90-429E-8C91-C0492B22C9D9.webp
 
In the world of astronomy, there is something called the "Japanese inch". This arose from a mistake (I think in the 1960s) where an inch, which is 25.4mm was mistakenly interpreted as 24.5mm. So Japanese eyepieces were made this size. So eyepiece barrel diameters are found as 0.96" (i.e. Japanese inch), 1", 1.25" (aka 37mm), and 2" (known as 50mm...).

The whole world of sizes and standards is a minefield.
 
Weirder still... there seems to be US metric and UK metric threads?

Whoever heard of M1.7, M2.3 and M2.6? As here: https://www.saxontheweb.net/threads/yamaha-stack-screw-rod-thread-spec.83886/#post-808412

...and a little later, someone else says there isn't such a thing as M2.5: https://www.saxontheweb.net/threads/yamaha-stack-screw-rod-thread-spec.83886/#post-811976

News to me!

I just have these (including M2.5), plus M3:

View attachment 23027

I've checked my M3 x 0.5 tap and the pitch IS 0.5mm. The pivot screw plainly isn't, but it is almost bang on 3mm diameter.

Is this like US gallons not being the same as UK gallons? Does metric differ across the continents?

I think I need... @Stephen Howard or @griff136 to help me decide if it's me, or the world, which has gone mad!

:w00t:
For any thread size, there are multiple pitches. Some are essentially obsolete. Your copy of Machinery's Handbook will show you most of the pitches including oddball ones.
 
Late to this, but...
having had many Yamahas from various product lines,
it's always worth seeing how far back their factory documentation goes.
Because it is VERY thorough. They don't often list diameters and thread pitches,
but with the part numbers, the Google can do its fu.

As to threads, well, as long as humans have had lathes, they've made up their own pitches.
Threads- per- inch on Metric stock isn't all that uncommon. I've once or twice seen the
reverse, with threads in mm and stock in bananas. errr, inches.

I've recently found that a VERY comprehensive inch thread measure and a lathe that works in inches,
one can fake Metric threads very convincingly- 2.5mm x 50 tpi translated perfectly...
because the French (Beaugnier, in this case) also had a few standards of their own.

....and yep, just about anything you can imagine is in Machinery's.

t
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,072
Messages
578,574
Members
8,133
Latest member
walthang
Back
Top Bottom