Saxophone beginners Spittle sizzling between reed / mouthpiece Help!

you're not a mother???
I've seen mothers do things that even I (am I have 3 children) wouldn't do.

🙂I am actually, to one very stroppy teenage son, and as I used to say when asked if I am having anymore "I learn by my mistakes";}


Jx
(No he wasn't a mistake he just wouldn't sleep at night but he is very stroppy)>:)
 
For me it sounds like the combination of mouthpiece table/reed/ligature is not producng a flat/secure enough fit. Have you tried an alternative reed or a different ligature on the mouthpiece? Selmer. like Otto Link are not the most consistent mouthpieces and the Soprano is not a forgiving sax. It would useful to try and eliminate certain things from our enquiries as well as pondering on the relevant technique issues

I agree with Nick W about mouthpiece lay - the Selmer C* is only 0.047" (same as Yamaha 4C) and may need to be perfectly clean to avoid any sound interference.
 
It's mostly pure water, anyway....you blow warm damp air into a relatively cool tube and the water condenses 🙂
And youdo play with a nice clean mouth too, don't you? 🙂
I find plastic reeds are worse for this....cane reeds absorb some of it.
 
If I take the mouthpiece off and dry it and the reed,and the neck, its ok for a while then,it only hapens when I tongue (I suppose if you are tu tu tu tuing into the mouthpiece, you are slightly spitting?) legato no problem (the reed gets quite dry though) I wonder if this problem is amplified more on the sop? after all as the mouthpiece etc comes down in size, the mouth however stays the same size.
I think the moisture is between the reed and the mouthpiece face, and is vibrating as I play (and sizzle) A wider tip might help?
 
Hi All, thanks, sorted now! tried allsorts, tissue between face and reed..didnt work.blowing sucking, shouting at it! in the end I looked closely at the ligature and reed contact area, the ribs on the BG ligature were not all making contact (along the length) it was tight, but had to go unbearably tight to compress all the rubber ribs! So I got a Selmer two screw standard ligature and fitted that on tight...now the reed is pulled hard onto the mouthpiece face and gives less room for any moisture I guess, So problem solved, I do get a bit still, but it is managable.and normal from what i have read here, but it is not a problem any more,Wonder what the next problem will be?I think now I have eliminated all the problems that comes with a Sop. one at a time I can now spend some time on mouthpiece/reed selection.
Thanks for your help (but it was going a bit blue!) lol
 
Pleased to hear that you appear to have stopped the problem.

However, the reed should not be "...pulled hard onto the mouthpiece face...", and if it seems to need this it suggests to me that the reed is not flat.
The ligature tension should really be the absolute minimum to keep the reed in place, thereby allowing it maximum freedom to vibrate.

(Others, with more knowledge and experience, will, no doubt, correct me if I have the wrong idea!)
 
Last edited by a moderator:
Pleased to hear that you appear to have stopped the problem.

However, the reed should not be "...pulled hard onto the mouthpiece face...", and if it seems to need this it suggests to me that the reed is not flat.
The ligature tension should really be the absolute minimum to keep the reed in place, thereby allowing it maximum freedom to vibrate.

(Others, with more knowledge and experience, will, no doubt, correct me if I have the wrong idea!)

You are pretty much spot on but could be either reed or mouthpiece table. If a reed is moistened and then fixed onto the mouthpiece with the ligature pulled tight it would help to form a seal and if left like this without actually playing it might help mould the reed to the shape of the table. Afterwards he reed/ligature combination could then be affixed more lightly when played. If you are serious I suggest looking at a custom made mouthpiece so that the table is guaranteed to be flat, or sending any mouthpiece you buy to a refacer if it is not so. I purchased a Soprano Planet custom mouthpiece and it is a better player than all the others I've tried, with no extraneous sound and no need to overtighten the ligature. A custom made/refaced mouthpiece may be slightly more (includes the PPT, Ed Pillinger, Morgan Fry and others in UK) but you only need one.

Good that you are going in the right direction!
 
Of course that is a correct alternative cause, Tom...thanks.
I have never had a 'non-flat' mpc table, so I didn't think of it.
(BTW, where do you get Rigotti reeds? I'd like to try them 🙂 )
 
Last edited by a moderator:
Of course that is a correct alternative cause, Tom...thanks.
I have never had a 'non-flat' mpc table, so I didn't think of it.
(BTW, where do you get Rigotti reeds? I'd like to try them 🙂 )

You obviously think that you do not have a 'non-flat' mpc table..........
I get my Rigotti reeds from Howarth in UK - Worth checking the Rigotti website in case there are suppliers in Spain.
 
Last edited by a moderator:
Thanks, Tom.

There is a site in France, I found, which sells 'em in pkts of 3 ...... a good way of trying them.

Perhaps I should have more accurately said that I heve never been aware of having a mpc table which was not flat >:)
(As my suppliers have included Lamberson, JJDV, Pillinger/PPT, Drake, Mouthpiece Cafe and T Wanne, it seems a safe assumption!)
 
It does sound a safe bet!

I am playing Rigotti Jazz 2.5M on my set up - with a 0.076" mouthpiece. I like them very much, and a cheaper alternative than my beloved FL Excellence 2.5, being just slightly harder - same as a 2.5 Vandoren Java/Rico Jazz Select 2H.

Regards
Tom
 
Last edited by a moderator:

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,074
Messages
578,642
Members
8,134
Latest member
banjo
Back
Top Bottom