Tech/maintenance Screw board and dismantle a sax

tom9437

Member
Messages
174
Location
peterborough uk
Hi all. First Q if it’s ok.
Has anyone made a screw board. Or where I can buy a cheap one.?
2. So I have bought a cheap alto it’s a stag in lovely condition. I bought it to learn how to dismantle and hopefully get it back together again. I hope to attend the Trevor Head woodwind course asap. But just wanted to gain some experience while I can. Could anyone tell me exactly where to start please. So obviously start with neck and remove the octave mechanism. Now what lol. Hope someone can advise.
Thank you
Tom
 
Solution
I have been working on saxophones for quite a while and I remember starting right where you are. As you might imagine your question cannot be answered with a short answer. A while back I started a thread on SOTW on this topic and shared what I have learned from my experience. So Ya Wanna Learn Sax Repair

I make my own "rod boards" using a drill press and one of the templates attached below. The holes are not labeled, which at first might seem confusing, but with a little thought you can come up with an order you can remember. Most of the rods are different lengths so a bit of logic can lead you to the right one if you forget the pattern. It is important to leave the screws in the posts after the keys are removed.

1668368828113.png
I have been working on saxophones for quite a while and I remember starting right where you are. As you might imagine your question cannot be answered with a short answer. A while back I started a thread on SOTW on this topic and shared what I have learned from my experience. So Ya Wanna Learn Sax Repair

I make my own "rod boards" using a drill press and one of the templates attached below. The holes are not labeled, which at first might seem confusing, but with a little thought you can come up with an order you can remember. Most of the rods are different lengths so a bit of logic can lead you to the right one if you forget the pattern. It is important to leave the screws in the posts after the keys are removed.

1668368828113.png
 

Attachments

Vote:
Upvote 0
Solution
I dismantled my first sax as a child without any guidance whatsoever. If my young self could do it, I’m sure you can as well. Once you get it back together only to find it doesn’t play, you’ll learn how to put all the springs back and make other adjustments. You’ll also learn how to glue back all the corks and felts you knocked off, assuming you’re able to see where they all go. Have fun!
 
Vote:
Upvote 0
Just have at it. You can't ruin or devalue a Stagg.
It's not a car engine. Most bits only go in one place.
I would advise to learn how it works before dismantling.
Regulating a saxophone is difficult if you're not aware of which bits need to synchronise.
Maybe try a clarinet first. Not as much mechanism and less regulation.
 
Vote:
Upvote 0
I dismantled my first sax as a child without any guidance whatsoever. If my young self could do it, I’m sure you can as well. Once you get it back together only to find it doesn’t play, you’ll learn how to put all the springs back and make other adjustments. You’ll also learn how to glue back all the corks and felts you knocked off, assuming you’re able to see where they all go. Have fun!
Thank you
 
Vote:
Upvote 0
I’ve disassembled and reassembled a saxophone. It’s easier than one might think. The most difficult part was working out how all the bits in the upper stack fitted together.
Start with the palm keys and the right-hand side keys then the right pinky keys - all very easy.
Take lots of photos during disassembly.
Expect to get sore fingers from the pointed ends of the springs.
 
Vote:
Upvote 0
I leave the pivot screws in place, and keep the rods with their associated keys. I lay all the parts out on the table top in the order they come off, then reverse for assembly (lubricating the rods as they go back on the horn).

Enjoy getting to know your horn.
 
Vote:
Upvote 0
I’ve disassembled and reassembled a saxophone. It’s easier than one might think. The most difficult part was working out how all the bits in the upper stack fitted together.
Start with the palm keys and the right-hand side keys then the right pinky keys - all very easy.
Take lots of photos during disassembly.
Expect to get sore fingers from the pointed ends of the springs.
Thank you
 
Vote:
Upvote 0
Before, during and after, take a lot of pictures. Get some shoeboxes and put a cardboard divider in each. So I dismantle my sax by Note. After the neck octave mechanism which I put in a box labelled Neck, I do the Low Eb and C which I put in the boxes labelled…Eb and C. Keep the rods and screws with their stacks. Don’t mix them up. And so on. Then the LHS palm keys. (Keep taking pictures at each stage and jot down the position of any cork and felts. Then start removing from the low D to the top B and mind that G#. Then keep going as each bit becomes more accessible. The RHS palm keys are easy to remove too. Be very careful with the C#,B and Bb on the pinky table. Once you’ve removed everything you will have the body and the needles left. Wear protective goggles, mark/number each needle placement with a felt pen and remove the needles and stick them on a piece of corrugated cardboard with their corresponding number. If you change corks, make sure to note thickness, because a too thick/thin cork will cause trouble.
That’s my experience. Hope it helps.
 
Vote:
Upvote 0
Removing needle springs is a pretty advanced technique for most people. If and when a person gets to that point, I recommend taking a couple of photos of the sax and gluing them to pieces of cork board. Of course the springs in this photo were replaced. I used them to determine the length and diameter of the new spring. The second photo shows the silverware bins I use to store parts. They are labeled: Pam and Side Keys, Upper Stack, Lower Stack, Low Keys, Guards and Neck, and Miscellaneous

1668436789545.jpeg
1668437167171.webp
 
Last edited:
Vote:
Upvote 0
Before, during and after, take a lot of pictures. Get some shoeboxes and put a cardboard divider in each. So I dismantle my sax by Note. After the neck octave mechanism which I put in a box labelled Neck, I do the Low Eb and C which I put in the boxes labelled…Eb and C. Keep the rods and screws with their stacks. Don’t mix them up. And so on. Then the LHS palm keys. (Keep taking pictures at each stage and jot down the position of any cork and felts. Then start removing from the low D to the top B and mind that G#. Then keep going as each bit becomes more accessible. The RHS palm keys are easy to remove too. Be very careful with the C#,B and Bb on the pinky table. Once you’ve removed everything you will have the body and the needles left. Wear protective goggles, mark/number each needle placement with a felt pen and remove the needles and stick them on a piece of corrugated cardboard with their corresponding number. If you change corks, make sure to note thickness, because a too thick/thin cork will cause trouble.
That’s my experience. Hope it helps.
Thank you
 
Vote:
Upvote 0
Once you’ve removed everything you will have the body and the needles left. Wear protective goggles, mark/number each needle placement with a felt pen and remove the needles and stick them on a piece of corrugated cardboard with their corresponding number.

Do you remove the springs everytime you strip the horn for cleaning and lubrication? I have never seen a need to remove the springs (even when cleaning a silver plate horn).
 
Vote:
Upvote 0
Do you remove the springs everytime you strip the horn for cleaning and lubrication? I have never seen a need to remove the springs (even when cleaning a silver plate horn).
I usually either delacquer or relacquer so remove the needles. I guess it depends what the operation is for.
 
Vote:
Upvote 0

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,076
Messages
578,677
Members
8,134
Latest member
banjo
Back
Top Bottom