Reeds Legere reeds - different reed for each mouthpiece?

eb424

Well-Known Member
Messages
4,216
Location
london
Morning..Ive started using the legere sig reeds..ive also tried a few hr mouthpieces over the year whilst mainly playing a 6* metal link with a 2.25 sig. Im hàppy with this set up..whilst trying cane reeds i will not use the same reed on different pieces as i think they form to the table..What is the general consensus on the sigs should i use a different reed per piece..will a quick dunk in boiling water reset them..
 
What is the general consensus on the sigs should i use a different reed per piece.
Good question. Theoretically yes, synthetics also form to the mouthpiece (note it’s facing curve rather than table assuming the table is flat). A quick play test for a few seconds should however not be too much of an issue.
will a quick dunk in boiling water reset them..
Yes but maybe to an extent, not necessarily 100%
[edit see below]
 
Last edited:
Morning..Ive started using the legere sig reeds..ive also tried a few hr mouthpieces over the year whilst mainly playing a 6* metal link with a 2.25 sig. Im hàppy with this set up..whilst trying cane reeds i will not use the same reed on different pieces as i think they form to the table..What is the general consensus on the sigs should i use a different reed per piece..will a quick dunk in boiling water reset them..
the dunk will reduce the hardness of legere reeds
 
I have found that a certain hardness will play better on one MP than another. Say a 2.0 Sig that plays well on one but a 2.25 or 2.5 works better on one of my other MPs. I am guessing that it has something to do with the facing and chamber size.
 
it might mould to the new piece whilst softer....
If it is the case that after dunking a synthetic becomes softer (and I'm sure there is no consensus on that apart from maybe while it is still hot) then it would probably be best to leave it (while in it's soften state ) in a reedholder or flatsurface so that it gets a chance to reflatten itslef.
 
Hmm so if id used one on a different piece and dunked it used it on another mouthpiece then it returns to normal strength..it might mould to the new piece whilst softer....
I only ever used the a dipping method few times when the reed was too hard for a particular mouthpiece which was an RPC 95F very open piece, but if your mouthpieces are of a similar opening and facing then there shouldn't be a need to dip it first.
 
Hmm so if id used one on a different piece and dunked it used it on another mouthpiece then it returns to normal strength..it might mould to the new piece whilst softer....
I move my Légère reeds from mouthpiece to mouthpiece without any issue

Dunking in boiling water is pointless at best, potentially damaging at worst and is unnecessary
 
I was thinking more about this @eb424

Cane and polypro are very different materials, so rules for one don't necessarily govern the other

The underlying assumption in this thread is that both cane and polypro bend to accommodate mouthpiece table imperfections, and once bent they don't resume their previous shape, so they don't play well on other mouthpieces

However, I don't think cane bends, it absorbs moisture and swells under the ligature and into any unevennesses in the mouthpiece table. The rule of not moving cane reeds from mouthpiece to mouthpiece suggests that there is some permanent, irreversible change in the cane shape. So once swelling has occured, some or all of it remains

Polypropylene doesn't absorb water and so doesn't deform in that way. Nevertheless there is an assumption in this thread that Légères do deform on the mouthpiece table and that they deform permanently. I doubt that I or anyone else tightens the lig sufficiently to reshape the body of a Légère, because they are so robust, however...

If you really, really overtighten the lig over a Légère reed, you might squish the reed out of true on an uneven mouthpiece table. But then if you're in the habit of applying that much lig pressure, your poor abused Légère will yield and squish into the next mouthpiece anyway
 

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,058
Messages
578,325
Members
8,127
Latest member
PJ2116
Back
Top Bottom