Tech/maintenance Lawton ligature repair

saxmad

Member
Messages
110
Location
North Norfolk
The screw holding the reedplate it into the ligature screw is stuck within the lig screw. I've managed to saw it apart from the plate using a jewellers saw. The task is now to release the stub of the screw. The photo shows the silver coloured screw within the brass lig screw. T he first photo shows the silver screw inserted into the lig . Second photo shows the lig how it should be, albeit with the correct screw.
lig 1.webp
lig 2.webp


Do you advise heating it it and immediately cooling it to remove? I have messaged Lawton asking to purchase a new screw.
 
Why was it necessary to disassemble?
A bit late for heat. Threads on thumb screw are ruined. Was likely assembled with a permanent type thread locker gel. AKA Loctite red.

Grab onto what’s left of fastener @90° with a mole wrench. Heat, wrap thumbscrew with cloth and turn while hot. Don’t overheat the brass or you’ll make it soft. Permanently.
 
Why was it necessary to disassemble?
A bit late for heat. Threads on thumb screw are ruined. Was likely assembled with a permanent type thread locker gel. AKA Loctite red.

Grab onto what’s left of fastener @90° with a mole wrench. Heat, wrap thumbscrew with cloth and turn while hot. Don’t overheat the brass or you’ll make it soft. Permanently.
The answer to your first query - it had to be disassembled because the screw (in the photo) had a head that was applying pressure to the reed. The screw should be countersunk thus resulting in only the reedplate being in contact with the reed.

I followed your instruction and applied heat in order to release the offending screw and I await a respond from Lawton.

Thank you PigSquealer
 
The answer to your first query - it had to be disassembled because the screw (in the photo) had a head that was applying pressure to the reed. The screw should be countersunk thus resulting in only the reedplate being in contact with the reed.
So you have aquired this second hand ? I’ve never seen one.
That button head screw didn’t look proper to begin with. I was thinking maybe a cover plate on top ? Orginal was countersunk or riveted on maybe ? I would like to see how this turns out / ends.
 
The brass thumbscrew's toast. No need to try to remove the broken-off bit of steel screw. Your solution is going to look something like machining a new center part of brass, machining out the threaded brass part whose OD threads are totally buggered, and soldering the new part into the existing knob.

Or, just have a machine shop make up a whole new thumb screw from bar. We're not talking about rocket parts here.
 
So you have aquired this second hand ? I’ve never seen one.
That button head screw didn’t look proper to begin with. I was thinking maybe a cover plate on top ? Orginal was countersunk or riveted on maybe ? I would like to see how this turns out / ends.
I did buy the mp second hand and noticed the wrong replacement screw had been used. The button head screw you refer to is the original (I also use a Lawton on my tenor so know the design). Still awaiting a reply from Lawton themselves.
 
The brass thumbscrew's toast. No need to try to remove the broken-off bit of steel screw. Your solution is going to look something like machining a new center part of brass, machining out the threaded brass part whose OD threads are totally buggered, and soldering the new part into the existing knob.

Or, just have a machine shop make up a whole new thumb screw from bar. We're not talking about rocket parts here.
The internal thread of the centre (where the "stub" of the screw is. as shown in the first photo) is good and without any need for work. None of the screws in my workshop fit in terms of thread hence contacting Lawton.
 
Yeah, but the outside thread is seriously buggered. Again, how I'd fix that would be to make a new center post of brass (OD and ID threads), remove the existing center post with its buggered threads, drill through the knob, solder in the new center post. Obviously it would be easiest to start with a brass bolt of the correct thread; which you can find by measuring the OD and counting the threads per mm (or, just bite the bullet and buy a set of thread gauges).
 
I did buy the mp second hand and noticed the wrong replacement screw had been used. The button head screw you refer to is the original (I also use a Lawton on my tenor so know the design). Still awaiting a reply from Lawton themselves.
As turf mentions the outside thread of that thumb screw looks completely knackered. It doesn’t look like a DIE could be run over it to clean up the threads. I would sure like to know what kind of button head screw is countersunk. Visually none of it makes mechanical sense. Shouldn’t that plate make nice even/smooth contact to the reed side?
Can you please post a picture of your other that is correct.
 
Fantastic news :clapping: Could I talk you into posting a picture of the correct looking part please. I’m curious what the correct holding screw looks like.
Photos attached, as requested, of the replacement holding screw supplied by Lawton - it's merely a 1cm countersunk wood screw. My original post, with a pic, showed a somewhat different threaded screw.
 
Photos attached, as requested, of the replacement holding screw supplied by Lawton - it's merely a 1cm countersunk wood screw. My original post, with a pic, showed a somewhat different threaded screw.

A woodscrew ? That sounds most unlikely. A countersunk bolt or maybe self-tapper sounds more plausible. The pictures will help, once posted.

Rhys
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,062
Messages
578,397
Members
8,129
Latest member
Bartman
Back
Top Bottom