JayeNM
Well-Known Member
- Messages
- 3,849
- Location
- New Mexico, US
$825 is high as far as market value for a splitbell King. However, it has apparently been overhauled. Even in that shape, going back to the original OP's discussion here, the market just doesn't see these as equals of a Buescher True Tone nor Conn Chu.
Personally....I think Chus are overrated. I think BOTH splitbell Kings AND Martins come very close to a Chu.
I don't think TT's are overrated, however. I don't think the other 3 Mfr's managed what the TT's are (in Altos). (I just wish them damn snap-ins had been nixed way back when
)
So...IF, for example, the price of the King horn in question was....$725-750 or so...I would actually suggest to someone they BUY it.
It's significantly cheaper than what a Chu or TT in that shape goes for.
You'd have a good horn, really. It has the front F.
As I have stated before regarding old Kings...their reputation for poor intonation is a bit of a myth. When paired with a good matching mouthpiece (no rocket science there, go large chamber, relatively low baffle, nothing very expensive needed) their intonation is as good as any Chu.
Build quality...and I realize I am contradicting older posts in this thread...nothing lost there. I wholeheartedly DISagree with any intimations that the build quality, robustness, and precision of King 20's horns were below that of say a Conn or Buescher.
On the tech bench, that claim doesn't hold true.
This used to be said of King Sopranos. Poor intonation to the point of driving people crazy. For almost 20 years a King soprano was significantly cheaper to acquire than the other American models. A project one could literally be stolen for around $300. A refurbed one could only fetch perhaps $800ish, while Conns and Martins and Booshes got $1200-2000.
Guess what ? Not anymore.
In the past 4 years or so, nabbing a King straight soprano in any shape is gonna cost about the same as nabbing a Martin, Conn, or Boosh.
Why the change ? Probably because enough folks figured out that the intonation thing was way overblown. I say the same of their Altos, having refurbed around 20 of them.
Next: why have 2 Kings ? Like Conns and Martins, a 20's model of ANY mfr is significantly different from what they produced in the late 30's-60's.
It is a different horn from a Cleveland. Its attributes will not be redundant compared to your Cleveland. You play the two side by side,the sonic differences will be pretty clear. They both have nice things to offer there. And ergonomically, I think of all the 20's horns, Kings had the best designed pinky table as far as response and laying under the fingers goes.
My 2 cents. Horn looks nice, just a bit overpriced.
Personally....I think Chus are overrated. I think BOTH splitbell Kings AND Martins come very close to a Chu.
I don't think TT's are overrated, however. I don't think the other 3 Mfr's managed what the TT's are (in Altos). (I just wish them damn snap-ins had been nixed way back when
)So...IF, for example, the price of the King horn in question was....$725-750 or so...I would actually suggest to someone they BUY it.
It's significantly cheaper than what a Chu or TT in that shape goes for.
You'd have a good horn, really. It has the front F.
As I have stated before regarding old Kings...their reputation for poor intonation is a bit of a myth. When paired with a good matching mouthpiece (no rocket science there, go large chamber, relatively low baffle, nothing very expensive needed) their intonation is as good as any Chu.
Build quality...and I realize I am contradicting older posts in this thread...nothing lost there. I wholeheartedly DISagree with any intimations that the build quality, robustness, and precision of King 20's horns were below that of say a Conn or Buescher.
On the tech bench, that claim doesn't hold true.
This used to be said of King Sopranos. Poor intonation to the point of driving people crazy. For almost 20 years a King soprano was significantly cheaper to acquire than the other American models. A project one could literally be stolen for around $300. A refurbed one could only fetch perhaps $800ish, while Conns and Martins and Booshes got $1200-2000.
Guess what ? Not anymore.
In the past 4 years or so, nabbing a King straight soprano in any shape is gonna cost about the same as nabbing a Martin, Conn, or Boosh.
Why the change ? Probably because enough folks figured out that the intonation thing was way overblown. I say the same of their Altos, having refurbed around 20 of them.
Next: why have 2 Kings ? Like Conns and Martins, a 20's model of ANY mfr is significantly different from what they produced in the late 30's-60's.
It is a different horn from a Cleveland. Its attributes will not be redundant compared to your Cleveland. You play the two side by side,the sonic differences will be pretty clear. They both have nice things to offer there. And ergonomically, I think of all the 20's horns, Kings had the best designed pinky table as far as response and laying under the fingers goes.
My 2 cents. Horn looks nice, just a bit overpriced.
Last edited:
