Tech/maintenance How to keep my brown bits from becoming red bits?

I may sell it one day, but it wouldn't fetch much and I've an inkling I may prefer it to my YTS-62 purely as it seemed to have a more mellow, perhaps darker, sound when I played it after purchase a few months ago? Once it's fully fettled I'll try them side by side. Not done that yet.

Anyhow... key work done and waxed (no colour change). Cleaning the very dirty/dusty body I noticed a dent by the Eb tone hole which I guess the guard had hidden from me before...

20221125_173233.webp


The tone hole is still level, so I could leave it as part of the overall patina, but I have an intolerance of dents which I can't quite explain so I'm going to try out a new (to me) tech who I discovered by chance just "down the road", have chatted to, but not used as yet: Flute Clarinet Saxophone Service Sales | Kingston Woodwind | Barwell

Some other minor dings also...

20221125_173404.webp

20221125_173521.webp


...the discoloured bow protector was weird. The lacquer had formed a kind of blister which could be moved back and forth with a finger tip in a "wave" effect. After playing with it, I burst it and scraped the lacquer back as far as I could with a fingernail. Once again, polishing this back to shiny would be a chore so once I've fully cleaned the body I'll probably wax that too. I'll leave the final clean and polish until it's been to the tech for the dents/dings...
 
I may sell it one day, but it wouldn't fetch much and I've an inkling I may prefer it to my YTS-62 purely as it seemed to have a more mellow, perhaps darker, sound when I played it after purchase a few months ago? Once it's fully fettled I'll try them side by side. Not done that yet.

Anyhow... key work done and waxed (no colour change). Cleaning the very dirty/dusty body I noticed a dent by the Eb tone hole which I guess the guard had hidden from me before...

View attachment 21957

The tone hole is still level, so I could leave it as part of the overall patina, but I have an intolerance of dents which I can't quite explain so I'm going to try out a new (to me) tech who I discovered by chance just "down the road", have chatted to, but not used as yet: Flute Clarinet Saxophone Service Sales | Kingston Woodwind | Barwell
This is the classic result of not swabbing the horn after use, then storing it in its case without further attention. Moisture accumulates in the Eb tone hole and is slow to evaporate. That is NOT patina, that is corrosion.
 
I could attack the bow with some abrasive rotary wheels I have which @jbtsax put me on to...

Screenshot 2022-11-26 at 17.34.25.webp



...Just worried I may get a bit carried away. Plus, I'm sure even the finest one with leave marks which then have to be hand sanded. I used to do this with gunstock blanks, down to 1500 grade, so it's no big deal but it could be a lot of work. The polished brass could then be left to form a new, hopefully more uniform, patina.
 
That looks great John. I recall you saying you sometimes use wax over the finish. Did you on this one?

Why the maroon and not the finer grey wheel (if the same as mine, under)?...
I think I used carnauba wax on this one, but I am not sure. I just prefer the finish the maroon wheel creates. I can also get the same effect by using a larger wheel for my bench motor, and by using 3M sheets. I get the wheels from Rio Grande Jewelry.
1669497503568.webp
 
Last edited:
I gave it a go with the finest, 300 grit, wheel on the bow protector area.

Before, it looked like...

Screenshot 2022-11-27 at 17.57.09.webp


After 5 minutes with the dremel and abrasive wheel. Tricky to get into the corners...

20221127_115651.webp


...and another 20 minutes with 1200 emery paper, Brasso, Autosol, and elbow grease...

20221127_123518.webp


The dremel work was quite easy, though to do a whole horn would involve working around the posts, guard feet, and tone holes, and of course there's the key work too. I'm guessing John tried to keep the sanding lines all going in one direction?

For my purposes I polished the area so it matched in with the surrounding lacquered brass as far as possible. You can see the difference in colour which will gradually lessen as the brass ages, and then the polished area will darken further until it perhaps turns brown too. It is waxed and so may take a while to age.
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,075
Messages
578,673
Members
8,134
Latest member
banjo
Back
Top Bottom