Tech/maintenance How to fix sticky pads - stop them sticking

Solution
I use 1000 grit wet-or-dry sandpaper cut into a strip slightly wider than the tone hole. I wet the paper side with Naptha (lighter fluid) and pull it out from under the pad several times with light pressure with the paper side up. This cleans the surface of the pad and also the top of the tonehole. If this doesn't work, I remove the key, clean the pad again and rub a generous amount of fine teflon powder into the pores of the pad and brush/blow away the excess. If the pad sticks again after that process, it gets replaced.
I have to jump in again to say two things. One, my brand new Yamaha began sticking after just a few days. Not from built up deposits, but the moisture collects (that's what has to happen when you blow into it!) and that pad is closed unlike most or all of the others. Suddenly it becomes obvious as heck why that key (pad, actually) sticks. So I now dry it when done and put a piece of very thin paper in it whan I put it away.
Second, I've seen saxophones for decades and realized that the body and keys look like the spaceship Geiger designed for the movie Alien. What I never realized was how complicated the actual machine is. Springs, pads, and levers attached in a diabolically complicated scheme that argues against doing repairs yourself, unless you kow you have that kind of mechanical acumen, which I do not. I have taken apart and fixed plenty of electronics, often saving them from the bin. I've modified amps and pickups and dug deep into software, too. But a lever confounds me and the saxophone is nothing if not over a dozen levels connected in complex way. How Adolphe even thought of developed this thing is beyond me, but I am grateful he did.
 
Vote:
Upvote 0
How Adolphe even thought of developed this thing is beyond me, but I am grateful he did.

Coming from the other direction, I have been repading a couple of horn in the last couple of weeks, I cam to the same thought of recognition for the mastery of Mr Sax. Repairing sax is great. And the result is starting to be quite rewarding, not financially but in terms of playing a leakfree easy to blow horn. And I feel like I'm learning with each one I deal with.
 
Vote:
Upvote 0
Yes, I've cleaned it multiple times. Horn is going to be checked soon, but is this a common problem?
Unlike the sticking G# or C# pads that are normally down, and can be unstuck manually before playing, the bis pad is normally up and when I play an A or Bb (bis), it sticks. I'm a major producer of saliva, but this is new. I'm hoping maybe a spring adjustment when I bring it in in 2 weeks? Or maybe pad needs replacing? It's under warranty. Am I pressing too hard? WHat up?
 
Vote:
Upvote 0
Is this on your alto or sop?
Sorry, should have said alto (YAS-480 a few months new)
A spring adjustment may help. I've had problems with a couple of sticking keys that are normally up and spring tweaks fixed the problem.
I hope so! I had the foresight to book a checkup the day before I leave on a three day trip. I can't stand being at home with no alto!
 
Vote:
Upvote 0
Is this all the time or only when you play Bb?

I found the one on my Trevor James started to do this, too, but only when I used it to play Bb. I assume this was because it was pressed just a little harder than when activated but another key. The solution was, as you've already done, to clean the pad but don't forget to also clean the tone hole rim.
 
Vote:
Upvote 0
My technique is to clean the pad using a flattened cotton bud (Q-tip) and naptha (lighter fluid). Next I pull a strip of 1000 grit wet or dry sandpaper abrasive side down between the pad and the tone hole using moderate pressure on the key several times. Most of the time this corrects the sticking pad. If it does not the pad gets a light application of teflon powder where the tonehole contacts the leather---being sure to blow away any excess powder.

At this point if the pad is still sticky I remove the key and check the tonehole for "burrs". If burrs are found, they are removed and the key is reinstalled. If no burrs are present the pad is replaced. You can find burrs by feeling around the sides of tonehole with your index finger in an up and down motion. A burr will feel "sharp and rough" instead of smooth.

Strengthening the spring on the bis might help, but that is overcoming the "symptom" rather than addressing the real problem and may interfere with the regulation which is sensitive in that area of the saxophone.
 
Vote:
Upvote 0
Hmmmm drink? On stage? Me? Yeah, might have been the rum cocktail? But it's happened at home during long practice sessions, too.
@jbtsax that's certainly good advice, but is it normal with a horn that was bought new in December? True, I probably play it 2-4 hours a day, so that's probably 120 days x 3 = 360 hours. Still... We'll see what he tech says in May. Meanwhile, I did clean the chimney with lighter fluid on Q-Tip, because you've schooled me well. I have some 400 emery paper, it's the finest I have, but I'm loathe to use it on a new instrument that's going to the shop in a couple of weeks. We'll see what the guy says.
 
Vote:
Upvote 0
It may have nothing at all to do with you. Some manufacturers use pads that have undergone a "waterproofing" treatment that causes them to develop a sticky surface regardless of how the instrument is cleaned or cared for.

400 emery paper 😱😱😱😱😱
 
Vote:
Upvote 0

Similar threads... or are they? Maybe not but they could be worth reading anyway 😀

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,075
Messages
578,657
Members
8,134
Latest member
banjo
Back
Top Bottom