Tech/maintenance Good sources of brass tubes and sheet materials

djarossens

Member
Messages
42
Location
Switzerland
Reaching out to the community to ask for suggestions please.
I need to make some parts and am looking for suppliers of tube and sheet brass.
So my first question is what grades of brass are most suitable for saxophone parts ?
Secondly, in the UK and mainland Europe who would be suppliers I'm looking for sheet between 0.8 and 1.25 mm in thickness. For tubes a variety of diameters up to 40mm with wall thicknesses from 0.7 upto 1.25 mm

I took a quick look on Ferrees and Music medic and the choices are quite limited.

thanks for any helpful ideas
 
For formed parts - tube, neck, bell, and key cups - C26000
For machined parts - key rods & tubes, key arms - C36000

I can't help you with who would be appropriate metals suppliers in Europe and Britain. In the US for small quantities we'd buy typically from McMaster-Carr or MSC Supply, which are large general-purpose industrial suppliers that carry a huge range of products. I don't know who the equivalent suppliers are in Europe and Britain. A practicing mechanical engineer in your area is who you need to ask; or alternately the owner of a machine shop.

For large quantities every large city has more than one general metals distributor who'll sell sheet and bar stock in all kinds of alloys. If they have it in stock (and they certainly ought to have C26000 and C36000 in stock) in the sizes you need, minimum quantity will be smaller than if they have to order it. Actually, that's who I'd call first. If you need small quantities and they can't supply such small amounts, they'll probably know who the appropriate general-purpose industrial supplier is.
 
So far as I am aware, sheet brass used for saxophones is (UK) standard CZ108 yellow brass. Things like pant guards are normally about 1.2mm, bodies a bit thinner, I think 0.9mm. There are loads of companies supplying sheet, bar and tube brass in the UK. I am aware that at least some will sell you a small sample sheet for just a few pounds. Lots of them are geared up to supply industrial quantities, and I have no idea what they would charge to ship to Switzerland. However, if there are a multitude of companies which will supply such material in the UK, other countries in Europe with an ongoing manufacturing base, such as France, Germany and Belgium will doubtless have the same.

This will sound a bit off, I also know someone who has bought brass sheet from an eBay seller called Metal Off Cuts, and been very pleased with what was supplied. The clue's in the name, they're cheap and will sell a single sheet of CZ108 for not much money. Again, I don't know about shipping to Switzerland, but you can always ask them.
 
Just for curiosity I looked up CZ108 and find that in the Unified Numbering System (the worldwide standard) it's C27400, 61-64% Cu compared to 68.5-71.5% for C26000. Probably a bit less formable, but of course that's HIGHLY dependent on the temper. Most of these sheet alloys are not heat treated but rather get their temper from rolling and drawing and are typically available in grades called "quarter hard", "half hard", "three quarter hard" and "full hard". Now I"m not an expert on the metallurgy of copper alloys, but I BELIEVE that while it's possible to anneal brass to reduce its hardness and increase its elongation, I don't think it's possible to heat treat it to restore hardness, certainly not like is done with steel. If there are heat treatments of this type for brass, they're going to almost certainly be a lot more complicated than the common heat treatment of carbon steels.

So as always it's going to come to "it depends" - in this case, OP, "it depends" on what exactly you're planning to do with this metal and which parts you're planning to make.

I can't speak to the relative availability of different alloys in Europe and Britain; I can tell you that the two alloys I listed above (C36000 for machining from bar and C26000 for forming) are among the most common (if not THE most common) in the US.
 
Reaching out to the community to ask for suggestions please.
I need to make some parts and am looking for suppliers of tube and sheet brass.
So my first question is what grades of brass are most suitable for saxophone parts ?
Secondly, in the UK and mainland Europe who would be suppliers I'm looking for sheet between 0.8 and 1.25 mm in thickness. For tubes a variety of diameters up to 40mm with wall thicknesses from 0.7 upto 1.25 mm

I took a quick look on Ferrees and Music medic and the choices are quite limited.

thanks for any helpful ideas
A short progress update, after some hours on the struggle bus I have made progress and now need to clean up the keys so I can figure out how tall to leave the chimneys.
IMG_5177.jpg

IMG_5166.jpg
 

Social

New! Social Feeds

Look out for the navigation icon:

Follow CafeSaxophone

Latest Song of the Month

Trending

Forum statistics

Topics
32,069
Messages
578,509
Members
8,131
Latest member
Jef B
Back
Top Bottom